Error Messages
List of: Discussion Topic
Contents: Application Development Manual
ABL_ATTRIB_BAD_PROC blnd/blend/kernbool/ee_att/abl.msg

"Illegal procedure attempted for blend attribute"
ABL_BAD_EE_START_PT blnd/blend/kernbool/ee_att/abl.msg

"Bad starting point given for edge-edge blend geometry"
ABL_BAD_EF_START_PT blnd/blend/kernbool/ee_att/abl.msg

"Bad starting point given for edge-face blend geometry"
ABL_BAD_FF_START_PT blnd/blend/kernbool/ee_att/abl.msg

"Bad starting point given for face-face blend geometry"
ABL_BAD_RAD_FCN blnd/blend/kernbool/ee_att/abl.msg

"Unable to create valid radius function from given data"
ABL_BAD_VE_START_PT blnd/blend/kernbool/ee_att/abl.msg

"Bad starting point given for vertex-edge blend geometry"
ABL_BAD_VF_START_PT blnd/blend/kernbool/ee_att/abl.msg

"Bad starting point given for vertex-face blend geometry"
ABL_CAP_COMPLEX blnd/blend/kernbool/ee_att/abl.msg

"Situation detected too complex for capping"
ABL_CHG_PT_COMPLEX blnd/blend/kernbool/ee_att/abl.msg

"Geometric configuration around change point too complex"
ABL_CHG_PT_COMPLEX_EDGE blnd/blend/kernbool/ee_att/abl.msg

"Geometric configuration around change point on edge too complex"
ABL_CHG_PT_COMPLEX_FACE blnd/blend/kernbool/ee_att/abl.msg

"Geometric configuration around change point on face too complex"
ABL_CHG_PT_COMPLEX_VERT blnd/blend/kernbool/ee_att/abl.msg

"Geometric configuration around change point on vertex too complex"
ABL_CVXTY_VIOLATION blnd/blend/kernbool/ee_att/abl.msg

"Concave/convex blend is removing/adding material"
ABL_CVX_CALC_FAILED blnd/blend/kernbool/ee_att/abl.msg

"Automatic blend convexity calculation failed."
ABL_ENDCAP_COMPLEX blnd/blend/kernbool/ee_att/abl.msg

"Situation detected too complex for endcapping"
ABL_ENDCAP_FAIL blnd/blend/kernbool/ee_att/abl.msg

"Attempted endcap has failed"
ABL_ENT_WITH_NO_VERTS blnd/blend/kernbool/ee_att/abl.msg

"Entity with no verts found. Please manually specify help point."
ABL_EXT_FAIL blnd/blend/kernbool/ee_att/abl.msg

"Blend surface could not be extended enough for capping"
ABL_FIRST_ERR_MSG blnd/blend/kernbool/ee_att/abl.msg

"Internal error in blending"
ABL_GEOM_EDGE_STAT blnd/blend/kernbool/ee_att/abl.msg

"Non-toroidal blend geometry not moving along edge"
ABL_GEOM_NOT_IMPL blnd/blend/kernbool/ee_att/abl.msg

"Blend geometry for entities not implemented"
ABL_GEOM_NOT_IMPL_VE blnd/blend/kernbool/ee_att/abl.msg

"Vertex-edge blend geometry not implemented"
ABL_GEOM_NOT_IMPL_VF blnd/blend/kernbool/ee_att/abl.msg

"Vertex-face blend geometry not implemented"
ABL_GEOM_NOT_IMPL_VV blnd/blend/kernbool/ee_att/abl.msg

"Vertex-vertex blend geometry not implemented"
ABL_HLP_PT_CALC_FAILED blnd/blend/kernbool/ee_att/abl.msg

"Automatic help point calculation failed."
ABL_INCONS_SEGMS blnd/blend/kernbool/ee_att/abl.msg

"Segment structure inconsistent"
ABL_INSUFF_GEOM blnd/blend/kernbool/ee_att/abl.msg

"Sufficient legal geometry could not be made for these entities"
ABL_INTERNAL_ERR blnd/blend/kernbool/ee_att/abl.msg

"Advanced blending internal error"
ABL_LAST_ERR_MSG blnd/blend/kernbool/ee_att/abl.msg

"Internal error in blending"
ABL_NO_GEOM blnd/blend/kernbool/ee_att/abl.msg

"Blend geometry ill-defined or undefined"
ABL_NO_GEOM_EE blnd/blend/kernbool/ee_att/abl.msg

"Edge-edge blend geometry ill-defined or undefined"
ABL_NO_GEOM_EF blnd/blend/kernbool/ee_att/abl.msg

"Edge-face blend geometry ill-defined or undefined"
ABL_NO_GEOM_FF blnd/blend/kernbool/ee_att/abl.msg

"Face-face blend geometry ill-defined or undefined"
ABL_NO_GEOM_VE blnd/blend/kernbool/ee_att/abl.msg

"Vertex-edge blend geometry ill-defined or undefined"
ABL_NO_GEOM_VF blnd/blend/kernbool/ee_att/abl.msg

"Vertex-face blend geometry ill-defined or undefined"
ABL_NO_SEGMS blnd/blend/kernbool/ee_att/abl.msg

"No blend faces found to exist between entities"
ABL_OFF_SUPPORT blnd/blend/kernbool/ee_att/abl.msg

"Blend does not touch a blended entity"
ABL_RADIUS_BIG blnd/blend/kernbool/ee_att/abl.msg

"Blend radius too big"
ABL_RADIUS_SMALL blnd/blend/kernbool/ee_att/abl.msg

"Blend radius too small"
ABL_SIDECAP_COMPLEX blnd/blend/kernbool/ee_att/abl.msg

"Situation detected too complex for sidecapping"
ABL_SIDECAP_FAIL blnd/blend/kernbool/ee_att/abl.msg

"Attempted sidecap has failed"
ABL_TRANS_COMPLEX blnd/blend/kernbool/ee_att/abl.msg

"Transition onto next entity too complex to determine"
ABL_TRANS_COMPLEX_EDGE blnd/blend/kernbool/ee_att/abl.msg

"Transition from edge onto next entity too complex to determine"
ABL_TRANS_COMPLEX_FACE blnd/blend/kernbool/ee_att/abl.msg

"Transition from face onto next entity too complex to determine"
ABL_TRANS_COMPLEX_VERT blnd/blend/kernbool/ee_att/abl.msg

"Transition from vertex onto next entity too complex to determine"
ABORT_CHECKING intr/intersct/sg_husk/sanity/sanity.msg

"found first insane entity"
ACIS_CONTROL_C_EXIT base/baseutil/errorsys/errorbase.msg

"Control-C interrupt"
ACIS_EXCEPTION_ACCESS_VIOLATION base/baseutil/errorsys/errorbase.msg

"Access violation"
ACIS_EXCEPTION_ARRAY_BOUNDS_EXCEEDED base/baseutil/errorsys/errorbase.msg

"Array bounds exceeded"
ACIS_EXCEPTION_BREAKPOINT base/baseutil/errorsys/errorbase.msg

"Breakpoint"
ACIS_EXCEPTION_DATATYPE_MISALIGNMENT base/baseutil/errorsys/errorbase.msg

"Data type misalignment"
ACIS_EXCEPTION_FLT_DENORMAL_OPERAND base/baseutil/errorsys/errorbase.msg

"Float denormal"
ACIS_EXCEPTION_FLT_DIVIDE_BY_ZERO base/baseutil/errorsys/errorbase.msg

"Float divide by zero"
ACIS_EXCEPTION_FLT_INEXACT_RESULT base/baseutil/errorsys/errorbase.msg

"Float inexact result"
ACIS_EXCEPTION_FLT_INVALID_OPERATION base/baseutil/errorsys/errorbase.msg

"Invalid float operation"
ACIS_EXCEPTION_FLT_OVERFLOW base/baseutil/errorsys/errorbase.msg

"Floating point overflow"
ACIS_EXCEPTION_FLT_STACK_CHECK base/baseutil/errorsys/errorbase.msg

"Stack check"
ACIS_EXCEPTION_FLT_UNDERFLOW base/baseutil/errorsys/errorbase.msg

"Floating point underflow"
ACIS_EXCEPTION_INT_DIVIDE_BY_ZERO base/baseutil/errorsys/errorbase.msg

"Integer divide by zero"
ACIS_EXCEPTION_INT_OVERFLOW base/baseutil/errorsys/errorbase.msg

"Integer overflow"
ACIS_EXCEPTION_IN_PAGE_ERROR base/baseutil/errorsys/errorbase.msg

"Page error"
ACIS_EXCEPTION_PRIV_INSTRUCTION base/baseutil/errorsys/errorbase.msg

"Privileged instruction attempted"
ACIS_EXCEPTION_SINGLE_STEP base/baseutil/errorsys/errorbase.msg

"Single step"
ACOVR_INTERNAL covr/cover/repair_husk/acovr.msg

"An internal error occured in advanced covering"
ADDTANG_PROBLEM bool/boolean/kernbool/boolean/boolean.msg

"system inconsistency processing surface tangency"
ADD_NO_USECOUNT kern/kernel/kerndata/data/data.msg

"called add() on entity with no use count"
ADD_TO_CLOSED_BB kern/kernel/kerndata/bulletin/bulletin.msg

"adding bulletin to closed bulletin board"
AGERR_ALLOC kern/kernel/spline/agspline/aguser/aguser.msg

"AGLib unable to allocate memory"
AGERR_DATA kern/kernel/spline/agspline/aguser/aguser.msg

"AGLib data value error"
AGERR_DEALLOC kern/kernel/spline/agspline/aguser/aguser.msg

"AGLib unable to deallocate memory"
AGERR_FOPEN kern/kernel/spline/agspline/aguser/aguser.msg

"AGLib unable to open file"
AGERR_INIT kern/kernel/spline/agspline/aguser/aguser.msg

"AGLib inappropriately initialized"
AGERR_ITER kern/kernel/spline/agspline/aguser/aguser.msg

"AGLib iteration fails to converge"
AGERR_MISSING kern/kernel/spline/agspline/aguser/aguser.msg

"AGLib missing algorithm for this case"
AGERR_OVERFLOW kern/kernel/spline/agspline/aguser/aguser.msg

"AGLib data array overflow"
AGERR_RANGE kern/kernel/spline/agspline/aguser/aguser.msg

"AGlib data out of range"
AGERR_READ kern/kernel/spline/agspline/aguser/aguser.msg

"AGLib error reading from file"
AGERR_STRUCT kern/kernel/spline/agspline/aguser/aguser.msg

"AGLib invalid structure"
AGERR_TRACE kern/kernel/spline/agspline/aguser/aguser.msg

"AGLib trace back"
AGERR_UNKNOWN kern/kernel/spline/agspline/aguser/aguser.msg

"AGLib unknown error"
ALGORITHM_TRAP base/baseutil/rtchecks/rtchecks.msg

"Algorithm trap"
ALREADY_FREE kern/kernel/kerndata/data/data.msg

"attempt to free record already on free list"
ALREADY_LOST kern/kernel/kerndata/data/data.msg

"attempt to delete record already marked as deleted"
API_FAILED kern/kernel/kernapi/api/api.msg

"operation unsuccessful"
AUTO_CLIP_UNSUPPORTED fct/faceter/api/facet.msg

"Auto Clipping no longer supported"
AXIS_NOT_MADE kern/kernel/sg_husk/sweep/sweep.msg

"Problem encountered computing axis"
AXIS_N_PLANE kern/kernel/sg_husk/sweep/sweep.msg

"Axis is not on the plane face"
BAD_ALLOC kern/kernel/kerndata/data/data.msg

"attempt to make data structure record static or on stack"
BAD_ANNOTATION_FOUND kern/kern_scm/kern_scm.msg

"Bad ANNOTATION found matching the given criteria"
BAD_ARRAY base/baseutil/mmgr/mmgr.msg

"Deleting a heap array allocated as an ordinary block"
BAD_ARRAY_ITEM base/baseutil/mmgr/mmgr.msg

"Item size mismatch deleting an array"
BAD_ARRAY_LENGTH base/baseutil/mmgr/mmgr.msg

"Length mismatch deleting an array"
BAD_ATTACH kern/kernel/kerndata/bulletin/bulletin.msg

"attach delta state must be beginning of branch"
BAD_ATTRIB kern/kernel/kerndata/data/data.msg

"attempt to create ATTRIB record"
BAD_ATTRIB_TAG kern/kernel/kerndata/data/data.msg

"callback created bad tag for annotation"
BAD_ATTRIB_TRANSFER bool/boolean/kernbool/boolean/boolean.msg

"cannot transfer INTCOED or shell_lump pointers"
BAD_AUTO_CHECK kern/kernel/kerndata/bulletin/bulletin.msg

"auto-checkpoint stacking error"
BAD_BEZIER_SPAN kern/kernel/spline/agspline/bs3_crv/bs3_crv.msg

"a spline curve span could not be represented in Bezier form"
BAD_BINARY_FORMAT kern/kernel/kernutil/fileio/fileio.msg

"Illegal value for binary_format option"
BAD_BOUNDARY_COEDGE bool/boolean/kernbool/boolean/boolean.msg

"misclassified graph coedge - probably geometrical problem"
BAD_BOX_OPERATION base/baseutil/vector/vector.msg

"illegal operation on given box"
BAD_BS_LENGTH kern/kernel/spline/agspline/bs3_srf/bs3_srf.msg

"number of control points in save file incorrect"
BAD_BS_MULT kern/kernel/spline/agspline/bs3_crv/bs3_crv.msg

"knot multiplicity too large for spline"
BAD_COEDGE_RING bool/boolean/kernbool/boolean/boolean.msg

"cannot pair up coedges at vertex"
BAD_CONTAINMENT bool/boolean/kernbool/boolean/boolean.msg

"inconsistent containment of intersection curve"
BAD_CURVE kern/kernel/kerndata/data/data.msg

"attempt to create CURVE record"
BAD_DEGENERACIES kern/kernel/sg_husk/api/sgapi.msg

"degenerate edges on a surface"
BAD_DELETE_ALL_STATES kern/kernel/kerndata/bulletin/bulletin.msg

"invalid links during delete"
BAD_DELETE_BB kern/kernel/kerndata/bulletin/bulletin.msg

"deleting bulletin board - not in list"
BAD_DIMENSION kern/kernel/spline/agspline/bs3_srf/bs3_srf.msg

"spline with incorrect dimensionality in save file"
BAD_DISCARD_SIZE base/baseutil/mmgr/mmgr.msg

"Freelist slot length mismatch in discard"
BAD_DISPOSAL bool/boolean/kernbool/boolean/boolean.msg

"unexpected disposal value for double-sided face"
BAD_ENTITY kern/kernel/kerndata/data/data.msg

"attempt to create ENTITY record"
BAD_ENTITY_ID kern/kernel/kerndata/savres/savres.msg

"malformed entity identifier"
BAD_FACE_IN_BODY_EDGE_CRUMBLE bool/boolean/kernbool/boolean/boolean.msg

"Adjacent body edges do not have common vertex on this face"
BAD_FACE_OWNERSHIP bool/boolean/kernbool/boolean/boolean.msg

"face not owned by owner"
BAD_FACE_SPLIT phlv5/phlv5_husk/sg_husk/phlv5/phlv5.msg

"Preprocesser unable to split face"
BAD_FACE_UV_BOX_CACHE kern/kernel/sg_husk/face/faceutil.msg

"uv box cached in face is incorrect."
BAD_GEDGE_COUNT law/lawutil/main_law.msg

"The gedge destructor was called with a non-zero use count."
BAD_GRAPH_COUNT law/lawutil/main_law.msg

"The graph destructor was called with a non-zero use count."
BAD_GUIDE_OWNER covr/cover/repair_husk/acovr.msg

"Owner of guide curves must be a body"
BAD_GVERTEX_COUNT law/lawutil/main_law.msg

"The gvertex destructor was called with a non-zero use count."
BAD_INT_EDGE bool/boolean/kernbool/boolean/boolean.msg

"intersection edge with no INTEDGE attribute"
BAD_INT_VERTEX bool/boolean/kernbool/boolean/boolean.msg

"intersection vertex with bad or no attributes"
BAD_ISO_VERTEX intr/intersct/kernbody/faceprop/faceprop.msg

"coedge on isolated vertex has partner"
BAD_ISO_VERT_REL bool/boolean/kernbool/boolean/boolean.msg

"inconsistent relationships at a non-manifold vertex"
BAD_KNOT_ORDER kern/kernel/sg_husk/net/net.msg

"The knot values neither increase nor decrease."
BAD_LAW_DATA_USE_COUNT law/lawutil/main_law.msg

"The law_data destructor was called with a non-zero use count."
BAD_LAW_USE_COUNT law/lawutil/main_law.msg

"The law destructor was called with a non-zero use count."
BAD_LOOP_OWNERSHIP bool/boolean/kernbool/boolean/boolean.msg

"loop not owned by owner"
BAD_LOOP_TYPE_CACHE kern/kernel/geomhusk/geomhusk.msg

"loop type cached in loop is incorrect."
BAD_ORDER kern/kernel/kernint/intsfsf/intsfsf.msg

"start and end points reversed on curve"
BAD_ORIGINS intr/intersct/kernbody/massprop/massprop.msg

"attempt to sum mass properties with differing origins"
BAD_OWNER covr/cover/repair_husk/acovr.msg

"Owner of the circuits must be a body"
BAD_PCURVE kern/kernel/kerndata/data/data.msg

"attempt to create PCURVE record"
BAD_PRODUCT_ID kern/kernel/kerndata/savres/savres.msg

"could not save, the product id in Fileinfo must be populated with a name"
BAD_REALLOC base/baseutil/mmgr/mmgr.msg

"Reallocation of object already allocated"
BAD_RELINK_ENTITY bool/boolean/kernbool/boolean/boolean.msg

"attempt to relink other than vertex or wire"
BAD_REQUEST base/baseutil/mmgr/mmgr.msg

"Request for zero or negative length free store"
BAD_RESTORE_FILE kern/kernel/kerndata/savres/savres.msg

"could not open restore file"
BAD_RESTORE_LOCALE kern/kernel/kerndata/savres/savres.msg

"Unsupported restore_locale option specified"
BAD_SAVE_FILE kern/kernel/kerndata/savres/savres.msg

"could not open save file"
BAD_SAVE_FORMAT kern/kernel/sg_husk/vrbln/vrbln.msg

"Unable to save variable radius blends in the requested file format"
BAD_SAVE_VERSION kern/kernel/kerndata/savres/savres.msg

"save file version illegal or later than current"
BAD_SINGULARITIES law/lawutil/main_law.msg

"The singularites on the law are bad"
BAD_SPIRAL_START law/lawutil/main_law.msg

"The start of the spiral is specified on the normal axis, use a zero start radius to accomplish"
BAD_SPLINE_APPROX kern/kernel/sg_husk/net/net.msg

"Bad spline approximation"
BAD_SPLINE_OFFSET kern/kernel/spline/agspline/bs3_crv/bs3_crv.msg

"inconsistent spline offset results"
BAD_SPLIT_PARAM bool/boolean/sg_husk/split/split.msg

"specified split parameter is outside surface range"
BAD_SURFACE kern/kernel/kerndata/data/data.msg

"attempt to create SURFACE record"
BAD_TAG kern/kernel/kerndata/bulletin/bulletin.msg

"tag id is not valid in history stream"
BAD_TAG_CREATE kern/kernel/kerndata/data/data.msg

"creating an ATTRIB_TAG when annotations turned off"
BAD_TANGENT kern/kernel/kerngeom/curve/curve.msg

"curve with a tangent vector of zero length"
BAD_TAN_DIR kern/kernel/kernint/intsfsf/intsfsf.msg

"cannot find two limiting directions at a tangency"
BAD_TORUS_RADII kern/kernel/geomhusk/geomhusk.msg

"Abs value of major radius greater than minor radius and major radius < 0"
BAD_UNITS kern/kernel/kerndata/savres/savres.msg

"could not save, the units in Fileinfo must be valid"
BAD_UPDATE kern/kernel/kerngeom/surface/surface.msg

"No b-spline was found for the update"
BAD_UV_NET_DIR kern/kernel/sg_husk/net/net.msg

"Surface U and V are in the same or opposite direction."
BAD_VAR_BLEND kern/kernel/sg_husk/vrbln/vrbln.msg

"Possibly corrupt variable radius blend - should be reapplied"
BEND_ADD_ONE_REGION warp/warphusk/warpapi.msg

"One more bending position is added in addition to given position(s)"
BEND_ADD_REGIONS warp/warphusk/warpapi.msg

"More bending positions are added in addition to given position(s)"
BEND_COMPRESS warp/warphusk/warpapi.msg

"The bending configuration will compress/invalidate the entity."
BEND_INTO_AXIS warp/warphusk/warpapi.msg

"Bending direction parallel to bending axis."
BEND_NOT_IMPLEMENTED warp/warphusk/warpapi.msg

"NYI"
BEND_NOT_NEEDED warp/warphusk/warpapi.msg

"No faces or wires are bent under given configuration."
BEND_NOT_ORTHO warp/warphusk/warpapi.msg

"Bending direction is not perpendicular to the bending axis."
BEND_OUTSIDE_ENTITY warp/warphusk/warpapi.msg

"One or more of the specified points is in an invalid region."
BEND_OUTSIDE_REGION warp/warphusk/warpapi.msg

"Specified point(s) not within bending region."
BEND_PARAM_NOT_AGREE warp/warphusk/warpapi.msg

"Radius*Angle (in radian) is not equal to Width."
BEND_PARAM_NOT_POSITIVE warp/warphusk/warpapi.msg

"Invalid combination of bending radius, width, and angle."
BL_ASSERTION_VIOLATED blnd/blend/kernbool/blending/blending.msg

"Blending assertion violated"
BL_ATTRIB_BAD_PROC blnd/blend/kernbool/blending/blending.msg

"Illegal procedure attempted for blend attribute"
BL_BAD_INTERCEPT blnd/blend/kernbool/blending/blending.msg

"cannot find body edge to trim spring curve during capping."
BL_BAD_LOOP blnd/blend/kernbool/blending/blending.msg

"Bad loop created during blending"
BL_BAD_REVERSE blnd/blend/kernbool/blending/blending.msg

"bad surface surface intersections during capping"
BL_BAD_SLICES kern/kernel/sg_husk/vrbln/vrbln.msg

"error during variable radius marching"
BL_BAD_SPINE blnd/blend/kernbool/blending/blending.msg

"cannot iterate to spine pt. "
BL_BAD_VBL_BNDRY blnd/blend/kernbool/blending/blending.msg

"vertex blend boundary is malformed or unsuitable"
BL_BAD_ZERO_BL_ED blnd/blend/kernbool/blending/blending.msg

"incompatibly blended edge at bi-blend vertex"
BL_BLEND_FACES_INTSECT blnd/blend/kernbool/blending/blending.msg

"Blend sheet is self-intersecting and cannot be resolved"
BL_BLEND_NPER_RAD_FCN blnd/blend/kernbool/blending/blending.msg

"Periodic edge with variable radius function that is not periodic"
BL_BLEND_TOO_BIG blnd/blend/kernbool/blending/blending.msg

"blend radius too big for adjacent face, or edge curvature"
BL_CANNOT_REORDER blnd/blend/kernbool/blending/blending.msg

"blends too complex to reorder"
BL_CAP_COMPLEX blnd/blend/kernbool/blending/blending.msg

"could not find acceptable sequence of capping faces to trim blend face"
BL_CHAMFER_NOT_IMPL blnd/blend/kernbool/blending/blending.msg

"chamfer case not implemented"
BL_CHAMFER_TOO_BIG blnd/blend/kernbool/blending/blending.msg

"chamfer offset too big"
BL_CHAMF_3PTS_ALIGNED blnd/blend/kernbool/blending/blending.msg

"cannot create a chamfer plane as 3 defining pints lie on a straight line"
BL_CHAMF_BAD_GRAPH blnd/blend/kernbool/blending/blending.msg

"cannot chamfer vertex: bad intersection graph (bad offset or invalid convexity?)"
BL_CHAMF_CUT_BODY blnd/blend/kernbool/blending/blending.msg

"chamfer of a concave vertex intersects unrelated faces above the vertex"
BL_CHAMF_CUT_VOID blnd/blend/kernbool/blending/blending.msg

"chamfer of a convex vertex cuts a void beneath the vertex"
BL_CHAMF_EDGE_ERR blnd/blend/kernbool/blending/blending.msg

"vertex does not belong to the edge used to specify oofset"
BL_CHAMF_ERR blnd/blend/kernbool/blending/blending.msg

"unable to find spine (blend too big ?)"
BL_CHAMF_NO_GOOD_EDGES blnd/blend/kernbool/blending/blending.msg

"cannot find 3 suitable edges to position the chamfer plane"
BL_CHAMF_SPRING_ERR blnd/blend/kernbool/blending/blending.msg

"unable to find spring curve (offset too big?)"
BL_CHAMF_VRTX_IN_PLANE blnd/blend/kernbool/blending/blending.msg

"chamfer plane cannot pass through the vertex being chamfered"
BL_CHG_PT_COMPLEX_EDGE blnd/blend/kernbool/blending/blending.msg

"Geometric configuration around change point on edge too complex"
BL_CHG_PT_COMPLEX_FACE blnd/blend/kernbool/blending/blending.msg

"Geometric configuration around change point on face too complex"
BL_CHG_PT_COMPLEX_VERT blnd/blend/kernbool/blending/blending.msg

"Geometric configuration around change point on vertex too complex"
BL_CI_NOT_FINITE blnd/blend/kernbool/blending/blending.msg

"curve-interval must be finite"
BL_CURVES_DIFFER blnd/blend/kernbool/blending/blending.msg

"operator requires curve-intervals on the same curve"
BL_CUSP_GEOM_TOO_CMPLX blnd/blend/kernbool/blending/blending.msg

"cuspate geometry too complex to blend"
BL_DO_M_SH_ED_CP_SG_ERR blnd/blend/kernbool/blending/blending.msg

"Blend do mitre sheet end comp signaling error."
BL_EMPTY_INT_GRAPH blnd/blend/kernbool/blending/blending.msg

"bad wire body present"
BL_EMPTY_MARCH_INT kern/kernel/sg_husk/vrbln/vrbln.msg

"interval of working curve to be marched is empty"
BL_EMPTY_SEQUENCE blnd/blend/kernbool/blending/blending.msg

"no edges in sequence"
BL_EMPTY_SHEET blnd/blend/kernbool/blending/blending.msg

"empty sheet body made"
BL_END_TOO_CMPLX blnd/blend/kernbool/blending/blending.msg

"geometry or topology at end of blend too complex"
BL_FACES_NOT_SET blnd/blend/kernbool/blending/blending.msg

"left face, right face, or defining plane is not set"
BL_FLD_INT_BLD_BIG blnd/blend/kernbool/blending/blending.msg

"Surface-surface intersection failed. Blend may be too big."
BL_FOUR_ED_MXD blnd/blend/kernbool/blending/blending.msg

"blends must be same width at 4-edge mixed cvxty vertex"
BL_GEOM_CONSTRUCTION_FAILED kern/kernel/sg_husk/vrbln/vrbln.msg

"unable to construct Acis geometry for blend"
BL_GEOM_TOO_CMPLX blnd/blend/kernbool/blending/blending.msg

"geometry too complex to blend (blend may be too big)"
BL_INCOMP_RADII_AT_MERGE_VERTEX blnd/blend/kernbool/blending/blending.msg

"Incompatible (different) blend radii across a mergeable vertex."
BL_INCONS_SHEET blnd/blend/kernbool/blending/blending.msg

"consistent sheet face cannot be built (check smooth intercepts?)"
BL_INTERNAL_ERR blnd/blend/kernbool/blending/blending.msg

"Blending internal error"
BL_INT_OFF_CURVE blnd/blend/kernbool/blending/blending.msg

"start or end intersection not on intersection curve"
BL_MARCH_FAILED kern/kernel/sg_husk/vrbln/vrbln.msg

"marching failed for variable radius blend"
BL_MITRE_AWRY blnd/blend/kernbool/blending/blending.msg

"cannot find mitre details where open sheet ends meet"
BL_MITRE_TOO_CMPLX blnd/blend/kernbool/blending/blending.msg

"mitred vertex too complex to process"
BL_NARROW_SUPPORT blnd/blend/kernbool/blending/blending.msg

"Support face is too narrow to accomodate the blend."
BL_NEG_RADIUS kern/kernel/sg_husk/vrbln/vrbln.msg

"Zero or negative radius encountered"
BL_NON_EDVERT blnd/blend/kernbool/blending/blending.msg

"blended entities must be edges or vertices"
BL_NON_MAN_EDVERT blnd/blend/kernbool/blending/blending.msg

"non-manifold edge or vertex in or near blend"
BL_NON_U_CVXTY blnd/blend/kernbool/blending/blending.msg

"cannot blend a partly-convex, partly-concave edge"
BL_NOT_IMPLEM blnd/blend/kernbool/blending/blending.msg

"this blend not yet implemented"
BL_NOT_SINGLE_SOLID blnd/blend/kernbool/blending/blending.msg

"all edges in a smooth sequence must belong to a single solid"
BL_NO_BLEND_EDGE kern/kernel/sg_husk/vrbln/vrbln.msg

"unable to find blended edge for variable radius blend"
BL_NO_CAP blnd/blend/kernbool/blending/blending.msg

"no capping faces could be found"
BL_NO_CAP_EXTN blnd/blend/kernbool/blending/blending.msg

"geometry extention failure in capping"
BL_NO_CLEAN_INT blnd/blend/kernbool/blending/blending.msg

"no clean intersection between capping face and sheet face"
BL_NO_CUTS_MIXED blnd/blend/kernbool/blending/blending.msg

"cannot adjust lateral edge end with mixed convexity"
BL_NO_DEF_CURVE kern/kernel/sg_husk/vrbln/vrbln.msg

"unable to find defining curve for variable radius blend"
BL_NO_FACES_OR_BODY blnd/blend/kernbool/blending/blending.msg

"cannot find face(s) to place flat on"
BL_NO_FACE_AT_VERT blnd/blend/kernbool/blending/blending.msg

"cannot find lateral face at end vertex"
BL_NO_INIT blnd/blend/kernbool/blending/blending.msg

"call to initialise_blend_one omitted"
BL_NO_MATE blnd/blend/kernbool/blending/blending.msg

"mating topology or geometry for vertex blend not found"
BL_NO_MITRE_MIXED blnd/blend/kernbool/blending/blending.msg

"can only mitre edges of the same convexity"
BL_NO_PIPES blnd/blend/kernbool/blending/blending.msg

"new algorithms do not support pipes - rb_replace_pipe should be ON"
BL_NO_PROJ_CUR blnd/blend/kernbool/blending/blending.msg

"no projection curve during imprint"
BL_NO_SHEET_SURF blnd/blend/kernbool/blending/blending.msg

"sheet surface is missing"
BL_NO_SPR_CUR_INT blnd/blend/kernbool/blending/blending.msg

"spring curves do not intersect"
BL_NO_VTX_GEOM blnd/blend/kernbool/blending/blending.msg

"no vertex blend geom created"
BL_NO_X_CURVE blnd/blend/kernbool/blending/blending.msg

"cannot find cross curve (blend too big?)"
BL_OBLIQUECRVS_NOT_SAVED blnd/blend/kernbool/blending/blending.msg

"cannot save oblique cross curve data on blend"
BL_ON_PROP_EDGE blnd/blend/kernbool/blending/blending.msg

"a blended edge may not have the same face on each side"
BL_ON_SH_BNDRY blnd/blend/kernbool/blending/blending.msg

"a blend may not be set on the boundary of a sheet body"
BL_OWNER_NOT_EDGE blnd/blend/kernbool/blending/blending.msg

"blend attribute's owner must be an EDGE"
BL_POINT_CUR blnd/blend/kernbool/blending/blending.msg

"error in point_cur"
BL_POINT_CUR_SURF blnd/blend/kernbool/blending/blending.msg

"error in point_cur_surf"
BL_RADIUS_CALIBRATION kern/kernel/sg_husk/vrbln/vrbln.msg

"unable to calibrate radius function"
BL_SETBACK_MISSING blnd/blend/kernbool/blending/blending.msg

"a zero-sized blend should be set back at a blended vertex"
BL_SETBACK_TOO_LARGE blnd/blend/kernbool/blending/blending.msg

"combination of edge setbacks is longer than the edge"
BL_SMOOTH_EDGE blnd/blend/kernbool/blending/blending.msg

"cannot blend a smooth edge"
BL_SMOOTH_LATERAL blnd/blend/kernbool/blending/blending.msg

"unblended smoothly connected lateral edge(s) at 4-edge mixed cvxty vertex"
BL_STOPS_NOT_SAVED blnd/blend/kernbool/blending/blending.msg

"cannot save stopping angle for old version"
BL_STOP_CMPLX blnd/blend/kernbool/blending/blending.msg

"location for stopping blend too complex"
BL_TOO_MANY_SM_EDS blnd/blend/kernbool/blending/blending.msg

"too many smooth edges at bi-blend vertex"
BL_TRANS_COMPLEX_EDGE blnd/blend/kernbool/blending/blending.msg

"Transition from edge onto next entity too complex to determine"
BL_TRANS_COMPLEX_FACE blnd/blend/kernbool/blending/blending.msg

"Transition from face onto next entity too complex to determine"
BL_TRANS_COMPLEX_VERT blnd/blend/kernbool/blending/blending.msg

"Transition from vertex onto next entity too complex to determine"
BL_UNBL_VERTEX blnd/blend/kernbool/blending/blending.msg

"cannot assign vertex blend to a bi-blend vertex"
BL_UNFIN_SHEET blnd/blend/kernbool/blending/blending.msg

"unable to complete sheet - blend may be too big"
BL_UNKNOWN_BLEND blnd/blend/kernbool/blending/blending.msg

"blend of unknown type or on unexpected entity"
BL_UNKNOWN_CVXTY blnd/blend/kernbool/blending/blending.msg

"unknown convexity"
BL_VTX_EDGE_UNBL blnd/blend/kernbool/blending/blending.msg

"an edge at a general vertex blend should be blended"
BL_VTX_NOT_IN_LIST blnd/blend/kernbool/blending/blending.msg

"must fix blended vertex and its blended edge together"
BODY_EDGE_CRUMBLE intr/intersct/kerndata/makeint/makeint.msg

"coincident face_face_ints with different body edges"
BODY_NO_SHELLS bool/boolean/kernbool/boolean/boolean.msg

"boolean operation on body with no shells"
BODY_VERTEX_CRUMBLE intr/intersct/kerndata/makeint/makeint.msg

"coincident face_face_ints with different body vertices"
BOUNDED_SURFACE_ERROR kern/kernel/kerngeom/surface/surface.msg

"save file version too early for bounded surface"
BOX_WARP_DOMAIN law/lawutil/main_law.msg

"The domain of box-warp-law is 0<x<1 in all 3 dimensions"
BS3_COI_VERTS kern/kernel/sg_husk/api/sgapi.msg

"error in control point coincidence"
BS3_CURVE_NULL kern/kernel/sg_husk/api/sgapi.msg

"edge has no underlying BS3 curve"
BS3_INCORRECT_DIMENSION kern/kernel/spline/agspline/bs3_crv/bs3_crv.msg

"bs3_curve dimension must be 1, 2, or 3"
BS3_SURF_NULL kern/kernel/sg_husk/api/sgapi.msg

"face has no underlying BS3 surface"
BS_ACCURACY law/lawutil/main_law.msg

"The bs3_surface is not within the requested tolerance."
BULLETIN_NOT_ON_BOARD kern/kernel/kerndata/bulletin/bulletin.msg

"remove bulletin from bulletin board it was not on"
BULLETIN_SEQUENCE kern/kernel/kerndata/bulletin/bulletin.msg

"Bulletins out of sequence after merge"
CALL_TO_BUY_OPER kern/kernel/geomhusk/geomhusk.msg

"OPER component is not installed."
CANNOT_DO_SURFACE intr/intersct/kernbody/massprop/massprop.msg

"surface unsuitable for current mass property code"
CANT_BUILD_ELEM_LOOP kern/kernel/meshhusk/mesh/mesh.msg

"unable to construct closed loop on boundary element"
CANT_FIND_NEW_TRI kern/kernel/meshhusk/mesh/mesh.msg

"unable to find valid node in retriangulation algorithm"
CANT_WRITE_MESH kern/kernel/meshhusk/surface/meshsur.msg

"cannot save out mesh class in old version format"
CHAIN_BAD_ORDER kern/kernel/sg_husk/sweep/sweep.msg

"The chain of coedges to be swept are not connected properly."
CHAIN_BRANCHING kern/kernel/sg_husk/sweep/sweep.msg

"The chain of coedges to be swept have branches."
CHAIN_NO_ENDS kern/kernel/sg_husk/sweep/sweep.msg

"The chain of coedges to be swept do not end."
CHAIN_NO_OWNER kern/kernel/sg_husk/sweep/sweep.msg

"The chain of coedges to be swept have no owner."
CHAIN_PARALLEL_PATH kern/kernel/sg_husk/sweep/sweep.msg

"The chain to be swept is parallel to the path"
CHANGE_DEFAULT_UNBALANCED_BB kern/kernel/kerndata/bulletin/bulletin.msg

"changing the default stream when bulletin board nesting unbalanced"
CHANGE_LOST_ENT kern/kernel/kerndata/data/data.msg

"attempt to change record marked as deleted"
CHANGE_PLANE_U_DERIV kern/kernel/kerngeom/surface/surface.msg

"WARNING: bad u parametrization vector on plane has been changed"
CHANGE_TORUS_UV_ORIGIN kern/kernel/kerngeom/surface/surface.msg

"WARNING: bad uv origin vector on torus has been changed"
CHECK_BAD_EE_INT bool/boolean/sg_husk/sanity/check.msg

"improper edge/edge intersection"
CHECK_BAD_FF_COIN bool/boolean/sg_husk/sanity/check.msg

"improper face/face coincidence"
CHECK_BAD_FF_INT bool/boolean/sg_husk/sanity/check.msg

"improper face/face intersection"
CHECK_BAD_LUMP_CONT bool/boolean/sg_husk/sanity/check.msg

"improper lump containment"
CHECK_BAD_SHELL_CONT bool/boolean/sg_husk/sanity/check.msg

"improper shell containment"
CHECK_FAILED_FF_INT bool/boolean/sg_husk/sanity/check.msg

"intersection failure"
CHECK_UNINIT intr/intersct/sg_husk/sanity/sanity.msg

"error unitialized"
CHORD_NOT_PERP cstr/constrct/kernwire/wire/wire.msg

"segment chord not perpendicular to normal"
CLEAR_UNBALANCED_BB kern/kernel/kerndata/bulletin/bulletin.msg

"HISTORY_STREAM::clear() when bulletin board nesting unbalanced"
CLOSED_EDGE cstr/constrct/kernwire/ewire/ewire.msg

"Closed edge in multi-edge wire"
CLOSED_EXTENSION kern/kernel/kerngeom/intcur/intcur.msg

"attempt to extend closed curve"
CLOSED_LOOP intr/intersct/kernint/divcon/divcon.msg

"Unexpected closed loop in divide-and-conquer"
CMPLX_PROF kern/kernel/sg_husk/sweep/sweep.msg

"Sweep profile too complex for sweep with draft"
COEDGES_OUT_OF_ORDER kern/kernel/kerndata/savres/savres.msg

"coedges are out of order on loop"
COEDGE_NO_EDGE kern/kernel/kerndata/top/top.msg

"coedge has a NULL edge pointer"
COEDS_DIFF_FACE eulr/euler/kerndata/euler/euler.msg

"given coedges must belong to the same face"
COINCIDENT_FACES stitch/stchhusk/stitch/stchutil/stitchr.msg

"Attempting to stitch coincident faces is not allowed"
COINCIDENT_POINTS kern/kernel/geomhusk/geomhusk.msg

"Coincident points"
COINCIDENT_WIRE bool/boolean/kernbool/boolean/boolean.msg

"cannot yet handle embedded wires"
COIN_ERROR kern/kernel/spline/agspline/bs3_crv/bs3_crv.msg

"Unable to remove coincident points with the given knot vector."
COLLINEAR_POINTS kern/kernel/geomhusk/geomhusk.msg

"Collinear points"
COMP_W_DRAFT kern/kernel/sg_husk/sweep/sweep.msg

"Complete sweep with draft"
CONST_WITH_THUMBWTS abl/abl_scm/ablscm.msg

"Cannot do const_radius ent_ent blends with thumbweights"
CONT_CRUMBLE intr/intersct/kerndata/makeint/makeint.msg

"inconsistent containments on coincident face_face_ints"
CORNER_TANGENCY intr/intersct/kernint/divcon/divcon.msg

"Special tangency case not yet implemented"
CORRUPT_BB kern/kernel/kerndata/bulletin/bulletin.msg

"Current bulletin board is corrupt."
CORRUPT_STREAM kern/kernel/kerndata/bulletin/bulletin.msg

"live entity on stream points to dead or deleted entity"
COULD_NOT_COVER covr/cover/sg_husk/cover/cover.msg

"Cover failed to make a surface"
COULD_NOT_FILLET law/lawutil/main_law.msg

"The requested fillet could not be made"
COVER_FACE_NULL kern/kernel/sg_husk/sweep/sweep.msg

"Unable to cover wires for sweep."
CROSS_NOT_TAN kern/kernel/kernint/intsfsf/intsfsf.msg

"crossing point found when tangency expected"
CRVS_DO_NOT_INT kern/kernel/sg_husk/net/net.msg

"Net curves do not intersect within net surface tolerance"
CRVS_INT_CROSS kern/kernel/sg_husk/net/net.msg

"Net curves intersections are not monotonic"
CURCUR_NOT_IMPL intr/intersct/kernint/intcucu/intcucu.msg

"curve-curve intersection not implemented yet"
CURVE_BAD_CLOSURE kern/kernel/sg_husk/api/sgapi.msg

"curve closure is wrong"
CURVE_IRREGULAR kern/kernel/sg_husk/api/sgapi.msg

"twisted or scrunched up curve"
CURVE_NON_C1 kern/kernel/sg_husk/api/sgapi.msg

"curve is not C1"
CURVE_NON_G0 kern/kernel/sg_husk/api/sgapi.msg

"curve is not G0"
CURVE_NON_G1 kern/kernel/sg_husk/api/sgapi.msg

"curve is not G1"
CURVE_NON_G2 kern/kernel/sg_husk/api/sgapi.msg

"curve is not G2"
CURVE_NOT_SPLIT cstr/constrct/geomhusk/geomhusk_cstr.msg

"Edge could not be split"
CURVE_REMESH_NOT_IMPL kern/kernel/meshhusk/mesh/mesh.msg

"remeshing on curved intersections is not implemented"
CURVE_SELF_INTER kern/kernel/sg_husk/api/sgapi.msg

"self-intersecting curve"
DEEP_COPY_MESH_NOT_IMPLEMENTED kern/kernel/meshhusk/surface/meshsur.msg

"deep_copy mesh not implemented"
DEEP_COPY_PATTERN_FILLED_PTR kern/kernel/kerndata/savres/savres.msg

"Deep copy contains pointer that has been pattern filled."
DEEP_COPY_TEST_NON_DEBUG kern/kernel/kerndata/savres/savres.msg

"Test:deep-copy does not pattern fill in non-DEBUG builds of ACIS."
DEEP_COPY_UNSUPPORTED kern/kernel/kerndata/savres/savres.msg

"Attempt to deep copy an unsupported entity."
DEF_EDGE_NOT_SELECTED abl/abl_scm/ablscm.msg

"Def edge must be selected for var radius ent-ent blending"
DEGENERATE_EDGE kern/kernel/sg_husk/api/sgapi.msg

"edge is degenerate"
DEGENERATE_FACE kern/kernel/sg_husk/api/sgapi.msg

"face is degenerate"
DETECT_PCURVE_TROUBLE phlv5/phlv5_husk/sg_husk/phlv5/phlv5.msg

"Gap in pcurves"
DETECT_SPLIT_EDGE phlv5/phlv5_husk/sg_husk/phlv5/phlv5.msg

"Split edge is processed as visible"
DIAG_FAILED intr/intersct/kernbody/massprop/massprop.msg

"diagonalisation of inertial tensor not completed"
DIAG_NEG intr/intersct/kernbody/massprop/massprop.msg

"one or more diagonal terms not positive"
DIFFICULT_CONFIGURATION kern/kernel/kernint/intsfsf/intsfsf.msg

"special-case method cannot handle this case"
DIFF_GEOM_COND bool/boolean/kernbool/boolean/boolean.msg

"Difficult geometric condition encountered and handled"
DIRTY_WIRE kern/kernel/sg_husk/sweep/sweep.msg

"Coedge has a partner. Try cleanwire before sweeping."
DISASTER intr/intersct/kernint/divcon/divcon.msg

"Unable to find split parameter for divide-and-conquer"
DISCONNECTED_WIRE cstr/constrct/geomhusk/geomhusk_cstr.msg

"Edges for wire are not connected"
DISCONN_EDS covr/cover/sg_husk/cover/cover.msg

"edge circuit is not connected"
DISCONTINUOUS_CURVE kern/kernel/kerngeom/intcur/intcur.msg

"curve is broken into two discontinuous pieces"
DOUBLE_ALLOC base/baseutil/mmgr/mmgr.msg

"Attempt to allocate an already allocated object"
DOUBLE_DELETE base/baseutil/mmgr/mmgr.msg

"Attempt to delete an already deleted object"
DRAFT_ON_SMOOTH kern/kernel/sg_husk/sweep/sweep.msg

"Draft Sweep for curved Path"
DRAFT_REPAIR kern/kernel/sg_husk/sweep/sweep.msg

"A topology change was caused by drafting"
DR_ANGLE_OR kern/kernel/sg_husk/sweep/sweep.msg

"The Draft angle results in a self intersecting body"
DS_ADMICON_ACIS_ERROR adm/admhusk/ds2acis/ds2acis.msg

"Admicon library returned an acis error"
DS_API_BAD_PATCH_DOMAIN adm/admhusk/ds2acis/ds2acis.msg

"patch domain not contained by parent or overlaps a sibling patch"
DS_API_NOT_A_QUAD_PATCH adm/admhusk/ds2acis/ds2acis.msg

"input face not a quad patch"
DS_API_NOT_A_ROOT_SIBLING adm/admhusk/ds2acis/ds2acis.msg

"input tag is not a sibling of the root dmod"
DS_API_NOT_COMMITED adm/admhusk/ds2acis/ds2acis.msg

"Must commit before performing this operation"
DS_API_NOT_FACE_OR_EDGE adm/admhusk/ds2acis/ds2acis.msg

"entity not sculptable (not a face or edge)"
DS_API_NOT_IN_HIERARCHY adm/admhusk/ds2acis/ds2acis.msg

"tgt_dmod value not a dmod tag value"
DS_API_NO_ATTRIB_DM2ACIS adm/admhusk/ds2acis/ds2acis.msg

"input attrib_dm2acis == NULL"
DS_ARRAY_OUT_OF_BOUNDS adm/admhusk/ds2acis/ds2acis.msg

"DM array out of bounds"
DS_BAD_ALPHA_VALUE adm/admhusk/ds2acis/ds2acis.msg

"Bad Alpha Vals - must be 0 or positive"
DS_BAD_ATTRIB_TYPE adm/admhusk/ds2acis/ds2acis.msg

"DS_error, unsupported attrib type seen"
DS_BAD_BETA_VALUE adm/admhusk/ds2acis/ds2acis.msg

"Bad Beta Vals - must be 0 or positive"
DS_BAD_BULLETIN_TYPE adm/admhusk/ds2acis/ds2acis.msg

"DS_error, unsupported bulletin type seen"
DS_BAD_CASCADE_FLAG_VALUE adm/admhusk/ds2acis/ds2acis.msg

"Bad cascade flag value = must be 0, 1, or 2"
DS_BAD_CASCADE_VALUE adm/admhusk/ds2acis/ds2acis.msg

"Bad cascade value - must be 0 to 3"
DS_BAD_CIRC_PARAM_VALUE adm/admhusk/ds2acis/ds2acis.msg

"circ param values must be from 0 to 2Pi"
DS_BAD_CIRC_SHAPE adm/admhusk/ds2acis/ds2acis.msg

"Specified circ degenerates to a line - axes are parallel or zero length"
DS_BAD_CIRC_TAG_FLAG adm/admhusk/ds2acis/ds2acis.msg

"DS_error, Bad circ tag flag - must be 1:add cstrn, 2:add load"
DS_BAD_CONTINUITY_VALUE adm/admhusk/ds2acis/ds2acis.msg

"bad continuity flag - must be 0=C0, 1=C1, 2=C2, or -1 to toggle C0,C1,C2"
DS_BAD_CONT_FLAG_VALUE adm/admhusk/ds2acis/ds2acis.msg

"input cont_flag must be 1 (elevate cont) or 0 (preserve cont)"
DS_BAD_CRV_CSTRN_DIM adm/admhusk/ds2acis/ds2acis.msg

"Bad curve constraint - domain_dim != 1"
DS_BAD_CRV_LOAD_DIM adm/admhusk/ds2acis/ds2acis.msg

"Bad curve load - domain_dim != 1"
DS_BAD_CRV_TOLERANCES adm/admhusk/ds2acis/ds2acis.msg

"DS_error, Can't commit because curve constraint tolerances are too large"
DS_BAD_CSTRN_BEHAVIOR adm/admhusk/ds2acis/ds2acis.msg

"Incorrect behavior setting: use DM_NORM to specify surface normal constraint"
DS_BAD_CSTRN_CHANGE adm/admhusk/ds2acis/ds2acis.msg

"requested cstrn state change prohibited for this cstrn"
DS_BAD_CSTRN_TYPE adm/admhusk/ds2acis/ds2acis.msg

"DS_error, unsupported constraint type seen"
DS_BAD_CSTRN_VAL_SIZE adm/admhusk/ds2acis/ds2acis.msg

"input cstrn_val_size is not correct for the selected constraint behavior"
DS_BAD_CURVATURE_VALUE adm/admhusk/ds2acis/ds2acis.msg

"input curvature value must be zero or positive"
DS_BAD_DAMP_VALUE adm/admhusk/ds2acis/ds2acis.msg

"input damp value has to be 0.0 or larger"
DS_BAD_DEGREE_VALUE adm/admhusk/ds2acis/ds2acis.msg

"requested spline degree must be 0 or greater"
DS_BAD_DELTA_VALUE adm/admhusk/ds2acis/ds2acis.msg

"Bad Delta Val - must be 0 or positive"
DS_BAD_DIR_FLAG_VALUE adm/admhusk/ds2acis/ds2acis.msg

"Bad dir flag - must be 1=project in xy dirs,2=project in z dir"
DS_BAD_DISP_GAIN_VALUE adm/admhusk/ds2acis/ds2acis.msg

"Bad disp gain - must not be 0, may be positive or negative"
DS_BAD_DMOD_FLAG_VALUE adm/admhusk/ds2acis/ds2acis.msg

"dmod_flag value must be 0, 1, or 2"
DS_BAD_DMOD_TYPE adm/admhusk/ds2acis/ds2acis.msg

"DS_error, unsupported def_model type seen"
DS_BAD_DOMAIN_DIM adm/admhusk/ds2acis/ds2acis.msg

"Bad domain dimension - must be 1=curves, 2=surfaces"
DS_BAD_DOMAIN_FLAG_VALUE adm/admhusk/ds2acis/ds2acis.msg

"domain_flag values: 0=orig_dmod_space, 1=unit-space, 2=internal_pfunc_space"
DS_BAD_DOMAIN_PT_RANGE adm/admhusk/ds2acis/ds2acis.msg

"Bad input par-pos domain loc - outside the 0 to 1 range"
DS_BAD_DRAW_MESH_VALUE adm/admhusk/ds2acis/ds2acis.msg

"Bad draw mesh values - must be greater than 0"
DS_BAD_DSGROUP_HIERARCHY adm/admhusk/ds2acis/ds2acis.msg

"DS_error, Failed to find ATTRIB_DSGROUP on ATTRIB_DSMODEL owner"
DS_BAD_DSMODEL_HIERARCHY adm/admhusk/ds2acis/ds2acis.msg

"DS_error, Failed to find ATTRIB_DSMODEL on DSGROUP base member owner"
DS_BAD_DT_VALUE adm/admhusk/ds2acis/ds2acis.msg

"input dt value has to be larger than 0.0"
DS_BAD_ELEM_COUNT adm/admhusk/ds2acis/ds2acis.msg

"Bad elem count - must be greater than 0"
DS_BAD_ELEM_COUNT_VALUE adm/admhusk/ds2acis/ds2acis.msg

"circ elem counts must be 5 or greater"
DS_BAD_ELLIPSE_RANGE adm/admhusk/ds2acis/ds2acis.msg

"requested ellipse does not fit in tgt_dmod"
DS_BAD_END_COND_VALUE adm/admhusk/ds2acis/ds2acis.msg

"Bad end cond - must be 0=open,1=closed,2=periodic"
DS_BAD_FIT_FLAG adm/admhusk/ds2acis/ds2acis.msg

"Bad fit flag value use 0=fit everywhere,1=fit cstrns,2=ignore tols"
DS_BAD_GEOM_CONDITION adm/admhusk/ds2acis/ds2acis.msg

"Solver error: poorly conditioned surface or pcurve"
DS_BAD_GROUP_FLAG_VALUE adm/admhusk/ds2acis/ds2acis.msg

"Bad group_flag - 0=set tag object only,1=set all loads of type"
DS_BAD_IMAGE_DIM_VALUE adm/admhusk/ds2acis/ds2acis.msg

"requested image dim must be larger than 0"
DS_BAD_INC_FLAG adm/admhusk/ds2acis/ds2acis.msg

"DS_error, Bad increment flag - must be 0:set_gain,1:inc_gain"
DS_BAD_INC_FLAG_VALUE adm/admhusk/ds2acis/ds2acis.msg

"Bad inc_flag - 0=set value absoluetly, 1=set value incrementally"
DS_BAD_INTER_STATE_VALUE adm/admhusk/ds2acis/ds2acis.msg

"Bad interior state value - must be 0=allow C0, or 1=enforce C1"
DS_BAD_IPT_FLAG_VALUE adm/admhusk/ds2acis/ds2acis.msg

"Bad image_pt flag - must be 0:free_pt=dpt_image_pt,1:free_pt=given_pt"
DS_BAD_KNOT_COUNT_VALUE adm/admhusk/ds2acis/ds2acis.msg

"spline knot count must be larget than 0"
DS_BAD_KNOT_TO_CPT_COUNT adm/admhusk/ds2acis/ds2acis.msg

"last knot index value not equal to dof_count + degree - 2"
DS_BAD_LOAD_TYPE adm/admhusk/ds2acis/ds2acis.msg

"DS_error, unsupported load type seen"
DS_BAD_MASS_VALUE adm/admhusk/ds2acis/ds2acis.msg

"input mass value has to be 0.0 or larger"
DS_BAD_MAX_DIST_VALUE adm/admhusk/ds2acis/ds2acis.msg

"Bad max dist - must be greater than 0.0"
DS_BAD_MERGE adm/admhusk/ds2acis/ds2acis.msg

"Attempting to merge invalid patch faces"
DS_BAD_NEGATE_FLAG_VALUE adm/admhusk/ds2acis/ds2acis.msg

"input negate_flag must be 1=negate or 0=don't"
DS_BAD_NTGRL_DEGREE_VALUE adm/admhusk/ds2acis/ds2acis.msg

"Requested Gauss Integration Degree not available"
DS_BAD_PATCH_AREA adm/admhusk/ds2acis/ds2acis.msg

"Cannot make a patch with a zero domain area"
DS_BAD_PATCH_CONTAINMENT adm/admhusk/ds2acis/ds2acis.msg

"Cannot make a patch which is not contained by its parent"
DS_BAD_PATCH_VERTEX adm/admhusk/ds2acis/ds2acis.msg

"Cannot make a patch with coincident child-parent vertices"
DS_BAD_POLYGON adm/admhusk/ds2acis/ds2acis.msg

"Input points do not specify a valid polygon"
DS_BAD_PT_COUNT_VALUE adm/admhusk/ds2acis/ds2acis.msg

"Bad point count - must be greater than 0"
DS_BAD_PT_INDEX_VALUE adm/admhusk/ds2acis/ds2acis.msg

"Bad pt_index value - does not id a valid image_pt in tag object"
DS_BAD_PURE_VIRTUAL_CALL adm/admhusk/ds2acis/ds2acis.msg

"DS_error - ran a base instead of derived pure virtual function"
DS_BAD_REFINEMENT_VALUE adm/admhusk/ds2acis/ds2acis.msg

"Patch knot refinement numbers must greater than or equal to 1"
DS_BAD_SCALE_PARAM_VALUE adm/admhusk/ds2acis/ds2acis.msg

"Scale parameter must be a non-zero number"
DS_BAD_SEAM_NUMBER_VALUE adm/admhusk/ds2acis/ds2acis.msg

"Bad seam number - must be in range 0 to seam_count - 1"
DS_BAD_SHAPE_DATA adm/admhusk/ds2acis/ds2acis.msg

"DS_error - incompatible ACIS and DS shape types-stopped Commit"
DS_BAD_SHAPE_FLAG_VALUE adm/admhusk/ds2acis/ds2acis.msg

"Bad default shape flag - must 0=zero,1=save"
DS_BAD_SHAPE_TYPE adm/admhusk/ds2acis/ds2acis.msg

"DS_error, unsupported ds surface or edge type seen"
DS_BAD_SHIFT_FLAG_VALUE adm/admhusk/ds2acis/ds2acis.msg

"tag_shift_flag vals: 0=don't shift tags, 1=do shift when needed"
DS_BAD_SINGULAR_VALUE adm/admhusk/ds2acis/ds2acis.msg

"Bad singular flag - must be 0=none,1=low_only,2=high_only,3=both"
DS_BAD_SLIDE_STATE adm/admhusk/ds2acis/ds2acis.msg

"Bad input slide_state input value, 0=fixed,1=sliding"
DS_BAD_SPLINE_DEGREE adm/admhusk/ds2acis/ds2acis.msg

"Can't set degree lower than 3"
DS_BAD_SRC_CURVE_TYPE adm/admhusk/ds2acis/ds2acis.msg

"Bad src type - not oneof ds_solid_cstrn, ds_bound_cstrn, ds_user_cstrn, ds_seam_cstrn"
DS_BAD_SRC_DATA_TGT_VALUE adm/admhusk/ds2acis/ds2acis.msg

"tgt value for Src_data calls must be the value 1 or 2"
DS_BAD_SRC_PFUNC_MAPPING adm/admhusk/ds2acis/ds2acis.msg

"a src_pfunc has an improper domain_dim or image_dim value"
DS_BAD_SRC_TYPE_PARENT adm/admhusk/ds2acis/ds2acis.msg

"src_type choice incompatible with parent_dmod value"
DS_BAD_STATE_FLAG_VALUE adm/admhusk/ds2acis/ds2acis.msg

"Bad state flag - must be 0=disable cstrn,1=enable cstrn,-1=toggle cstrn"
DS_BAD_SYNTAX_FLAG adm/admhusk/ds2acis/ds2acis.msg

"DS_error, Bad Syntax flag - must be 1:use free_curve,2:line,3:round"
DS_BAD_TAG_FLAG_VALUE adm/admhusk/ds2acis/ds2acis.msg

"Bad tag flag argument, must not be zero"
DS_BAD_TAG_VALUE adm/admhusk/ds2acis/ds2acis.msg

"Bad tag value - must be -1(sys assigns tag) or > 1"
DS_BAD_TOLERANCE_VALUE adm/admhusk/ds2acis/ds2acis.msg

"tolerance values must be larger than 0"
DS_BAD_TYPE_ID_VALUE adm/admhusk/ds2acis/ds2acis.msg

"input DS_TAGS type_id value not a valid DS_dmod type"
DS_BAD_UNITS_FLAG adm/admhusk/ds2acis/ds2acis.msg

"DS_error, max_dist_units must be 0=image_space_dist or 1=active_view_pixels"
DS_BAD_WALK_FLAG_VALUE adm/admhusk/ds2acis/ds2acis.msg

"walk_flag not 0 (dmod only), 1 (dmod,offspring), or 2 (dmod,siblings,all offspring)"
DS_BAD_WHICH_DIR_VALUE adm/admhusk/ds2acis/ds2acis.msg

"input which_dir value not valid"
DS_BAD_WUV_WVV_VALUES adm/admhusk/ds2acis/ds2acis.msg

"Wuv_vec and Wvv_vec must be NULL for pt_cstrns on curves"
DS_BAD_ZONE_FLAG_VALUE adm/admhusk/ds2acis/ds2acis.msg

"zone flag value must be 0=zone area moves or 1=zone area fixed"
DS_BSPLN_CONSTRUCT_FAILED adm/admhusk/ds2acis/ds2acis.msg

"Constructor for B-spline object failed"
DS_CANT_RM_ONLY_ROOT_DMOD adm/admhusk/ds2acis/ds2acis.msg

"Cannot use DM_rm_patch to remove last root dmod"
DS_CANT_RM_SRC_DMOD adm/admhusk/ds2acis/ds2acis.msg

"Can't remove cstrn src_dmod's this way, use DM_set_cstrn_src_dmods()"
DS_CG_UNCONVERGED adm/admhusk/ds2acis/ds2acis.msg

"Congrad solve failed to converge"
DS_CODE_NOT_COMPLETE adm/admhusk/ds2acis/ds2acis.msg

"Sorry, this function not complete in this Release"
DS_CONFLICTING_CONSTRAINT adm/admhusk/ds2acis/ds2acis.msg

"solve stopped due to a conflicting constraint"
DS_CSTRN_HAS_NO_SRC_PFUNC adm/admhusk/ds2acis/ds2acis.msg

"the crv_cstrn or link_cstrn is not using a src_W_pfunc"
DS_CSTRN_NOT_CONVERTIBLE adm/admhusk/ds2acis/ds2acis.msg

"can't convert cstrn - not a crv_cstrn or pt_cstrn"
DS_CUSTOMER_ERROR adm/admhusk/ds2acis/ds2acis.msg

"Customer-defined error signalled"
DS_DELETE_A_USED_PFUNC adm/admhusk/ds2acis/ds2acis.msg

"delete was called on a pfunc with a non-zero reference count"
DS_DIVERGENT_JOURNAL_RUN adm/admhusk/ds2acis/ds2acis.msg

"Journal file value differs from journal run value - stoping play"
DS_DMOD_CONSTRUCT_FAILED adm/admhusk/ds2acis/ds2acis.msg

"Constructor for DS_dmod object failed"
DS_DMOD_MISSING_PFUNC adm/admhusk/ds2acis/ds2acis.msg

"input dmod does not contain a valid DS_pfunc object"
DS_DMOD_NOT_A_CURVE adm/admhusk/ds2acis/ds2acis.msg

"Input dmod not a curve as expected"
DS_DMOD_NOT_A_ROOT_DMOD adm/admhusk/ds2acis/ds2acis.msg

"Given dmod not the hierarchy root as expected"
DS_DMOD_NOT_A_SURFACE adm/admhusk/ds2acis/ds2acis.msg

"Input dmod not a surface as expected"
DS_DMOD_NOT_IN_A_DMESH adm/admhusk/ds2acis/ds2acis.msg

"DS_dmod not part of a multi-surface dmesh structure"
DS_EDGE_BELONGS_TO_FACE adm/admhusk/ds2acis/ds2acis.msg

"Edge for deformable modeling must must NOT belong to a face"
DS_ENTITY_NOT_EDGE adm/admhusk/ds2acis/ds2acis.msg

"DS_error, entity not an EDGE as expected"
DS_ENTITY_NOT_FACE adm/admhusk/ds2acis/ds2acis.msg

"DS_error, entity not a FACE as expected"
DS_ENTITY_NOT_INTCURVE adm/admhusk/ds2acis/ds2acis.msg

"DS_error, entity not an INTCURVE as expected"
DS_ENTITY_NOT_SPLINE adm/admhusk/ds2acis/ds2acis.msg

"DS_error, entity not a SPLINE as expected"
DS_FACES_NOT_CONNECTED adm/admhusk/ds2acis/ds2acis.msg

"input multi-surface faces are not connected by at least one edge"
DS_FAILED_FILE_OPEN_READ adm/admhusk/ds2acis/ds2acis.msg

"Designated file failed to open for read"
DS_FAILED_FILE_OPEN_WRITE adm/admhusk/ds2acis/ds2acis.msg

"Designated file failed to open for write"
DS_FILLET_RADIUS_NOT_POS adm/admhusk/ds2acis/ds2acis.msg

"Fillet Radius has to be positive to fit in the shape"
DS_FILLET_RADIUS_TOO_BIG adm/admhusk/ds2acis/ds2acis.msg

"Fillet Radius is too large to fit in shape"
DS_HAS_CHILD adm/admhusk/ds2acis/ds2acis.msg

"Can't set degree when a child dmod is present"
DS_HAS_PARENT adm/admhusk/ds2acis/ds2acis.msg

"Can't set degree when a parent dmod is present"
DS_INCORRECT_BEHAVIOR_SPECIFIED adm/admhusk/ds2acis/ds2acis.msg

"Behavior argument should be one of DM_POSITION, DM_TANG, DM_CURVATURE"
DS_INITIALIZE_FAILURE adm/admhusk/ds2acis/ds2acis.msg

"SDM failed to initialize"
DS_INTERNAL_ERROR adm/admhusk/ds2acis/ds2acis.msg

"Unexpected internal error was encountered in Deformable Modeling"
DS_LINK_REQD_ON_EDGE adm/admhusk/ds2acis/ds2acis.msg

"DS_error, add link interface requires edge with existing link"
DS_LOAD_NOT_CONVERTIBLE adm/admhusk/ds2acis/ds2acis.msg

"can't convert load - not a crv_load, spring, or spring_set"
DS_LOW_DOF_CNT_WARNING adm/admhusk/ds2acis/ds2acis.msg

"DS_warning - low dof count - Consider ds:split-domain"
DS_MISSING_CRV_CSTRN adm/admhusk/ds2acis/ds2acis.msg

"could not find a crv_cstrn to match an ATTRIB_CRV_CSTRN object"
DS_MISSING_SRC_DATA adm/admhusk/ds2acis/ds2acis.msg

"crv_cstrn or link_cstrn curve-shape description inputs are inconsistent"
DS_MIXED_AREA_CSTRN_DIM adm/admhusk/ds2acis/ds2acis.msg

"Bad area constraint - zone domain_dim != deformable domain_dim"
DS_MIXED_CRV_CSTRN_DIM adm/admhusk/ds2acis/ds2acis.msg

"Bad curve constraint - image_dim != deformable domain_dim"
DS_MIXED_CRV_LOAD_DIM adm/admhusk/ds2acis/ds2acis.msg

"Bad domain_curve load - image_dim != deformable domain_dim"
DS_MIXED_DCRV_DIM adm/admhusk/ds2acis/ds2acis.msg

"dcrv's image_dim not equal to surface's domain_dim"
DS_MIXED_DOMAIN_DIMS adm/admhusk/ds2acis/ds2acis.msg

"DS_error, tag object and deformable domain dimensions differ"
DS_MIXED_FREE_LOAD_DIM adm/admhusk/ds2acis/ds2acis.msg

"Bad free_curve load - image_dim != deformable image_dim"
DS_MIXED_IMAGE_DIMS adm/admhusk/ds2acis/ds2acis.msg

"DS_error, tag object and deformable image dimensions differ"
DS_MULTI_FACE_NOT_SIMPLE adm/admhusk/ds2acis/ds2acis.msg

"for now; only one-root-sbiling faces can be added to mesh network"
DS_MULTI_SURF_EXTRAPOLATE adm/admhusk/ds2acis/ds2acis.msg

"Can't extrapolate a deformable model within a multi-surface mesh"
DS_NEG_CURVATURE_VALUE adm/admhusk/ds2acis/ds2acis.msg

"Curvature value for curves must be pos or NULL for undefined"
DS_NONMONOTONIC_LINK adm/admhusk/ds2acis/ds2acis.msg

"link dcrvs must be monotonic, dC/ds can not change sign for valid values of s"
DS_NON_BNDRY_QUILT_EDGE adm/admhusk/ds2acis/ds2acis.msg

"Edges between two def faces must be on face's boundary"
DS_NON_CONVEX_POLYGON adm/admhusk/ds2acis/ds2acis.msg

"Input points do not specify a convex polygon"
DS_NON_NULL_OUTPUT_PTR adm/admhusk/ds2acis/ds2acis.msg

"reference to output array ptrs are not NULL on entry"
DS_NOT_A_BSPLINE adm/admhusk/ds2acis/ds2acis.msg

"input pfunc type not a B-spline as expected"
DS_NOT_A_CIRC adm/admhusk/ds2acis/ds2acis.msg

"input pfunc type not a circ as expected"
DS_NOT_A_CRV_LINK_CSTRN adm/admhusk/ds2acis/ds2acis.msg

"identified constraint is not a curve or link constraint"
DS_NOT_A_JOURNAL_FILE adm/admhusk/ds2acis/ds2acis.msg

"Specified file is not a proper version journal file"
DS_NOT_A_NURB adm/admhusk/ds2acis/ds2acis.msg

"input pfunc type not a NURB as expected"
DS_NOT_A_PT_CSTRN adm/admhusk/ds2acis/ds2acis.msg

"identified constraint is not a point constraint"
DS_NOT_A_ROOT_SIBLING adm/admhusk/ds2acis/ds2acis.msg

"identified target dmod is not a sibling of the root"
DS_NOT_BSPLINE_OR_NURB adm/admhusk/ds2acis/ds2acis.msg

"dmod not a B-spline or nurb shape"
DS_NOT_DSGROUP_BASE adm/admhusk/ds2acis/ds2acis.msg

"DS_error, entity not ATTRIB_DSGROUP base member as expected"
DS_NOT_IN_SAME_DSGROUP adm/admhusk/ds2acis/ds2acis.msg

"DS_error, Two entities not in same DSGROUP as expected"
DS_NOT_IN_SAME_HIERARCHY adm/admhusk/ds2acis/ds2acis.msg

"DS_error, Two entities not in same Patch Hierarchy as expected"
DS_NOT_PARENT_CHILD adm/admhusk/ds2acis/ds2acis.msg

"DS_error, Two entities not are not a Parent-Child Patch as expected"
DS_NOT_USER_CSTRN adm/admhusk/ds2acis/ds2acis.msg

"can't convert cstrn - it is not a type ds_user_cstrn cstrn"
DS_NO_ACTIVE_DMOD adm/admhusk/ds2acis/ds2acis.msg

"There is no currently active member for the dmod hierarchy"
DS_NO_DOF_CNT_WARNING adm/admhusk/ds2acis/ds2acis.msg

"DS_warning - no dofs left to deform - Use ds:split-domain to add more"
DS_NO_DSGROUP_ATTRIB adm/admhusk/ds2acis/ds2acis.msg

"DS_error, ENTITY does not have an ATTRIB_DSGROUP attribute"
DS_NO_INTERSECTIONS adm/admhusk/ds2acis/ds2acis.msg

"input image_line does not intersect dmod shape"
DS_NO_ROOT_DMOD adm/admhusk/ds2acis/ds2acis.msg

"There is no root member for the dmod hierarchy"
DS_NO_UV_PT_FOR_TAG_OBJ adm/admhusk/ds2acis/ds2acis.msg

"can't get uv pt for this kind of tag object"
DS_NO_XYZ_PT_FOR_TAG_OBJ adm/admhusk/ds2acis/ds2acis.msg

"can't get xyz pt for this kind of tag object"
DS_NULL_INPUT_PTR adm/admhusk/ds2acis/ds2acis.msg

"input ptr to an array was NULL on input"
DS_NULL_OUTPUT_PTR adm/admhusk/ds2acis/ds2acis.msg

"required output ptr array is NULL on entry"
DS_PARALLEL_DOMAIN_DIRS adm/admhusk/ds2acis/ds2acis.msg

"the two domain_dir directions must not be parallel"
DS_PARALLEL_PROJECT_DIR adm/admhusk/ds2acis/ds2acis.msg

"set_pt_xyz project dir is parallel to target axis"
DS_PARAMETER_OFF_SURFACE adm/admhusk/ds2acis/ds2acis.msg

"pcurve evaluates off deformable surface"
DS_PATCH_OCCLUDES_ROOT adm/admhusk/ds2acis/ds2acis.msg

"Cannot make a patch which occludes the patch hierarchy root"
DS_PATCH_OVERLAPS_SIBLING adm/admhusk/ds2acis/ds2acis.msg

"Cannot currently make a patch which overlaps an existing sibling"
DS_PFUNC_CONSTRUCT_FAILED adm/admhusk/ds2acis/ds2acis.msg

"Constructor for DS_pfunc object failed"
DS_SEGMENTER_FAILURE adm/admhusk/ds2acis/ds2acis.msg

"Segmenter returned no segments or NULL pointer"
DS_SOLVE_NEVER_CONVERGED adm/admhusk/ds2acis/ds2acis.msg

"solve not converging - large pressure or attractor gains cause chaos"
DS_TAGOBJ_HAS_NO_PARAM adm/admhusk/ds2acis/ds2acis.msg

"DM tag object has no parameterization"
DS_TAGOBJ_NOT_A_CURVE adm/admhusk/ds2acis/ds2acis.msg

"DM tag object not a curve"
DS_TAGOBJ_NO_SRC_PFUNC_OR_FUNC adm/admhusk/ds2acis/ds2acis.msg

"DM tag object has no src pfunc or func"
DS_TAG_NOT_A_DMOD_MEMBER adm/admhusk/ds2acis/ds2acis.msg

"Given tag value does not identify a dmod in the hierarchy"
DS_TAG_NOT_CRV_CSTRN adm/admhusk/ds2acis/ds2acis.msg

"input tag number failed to find a crv_cstrn tag object"
DS_TAG_OBJECT_NOT_FOUND adm/admhusk/ds2acis/ds2acis.msg

"input tag number failed to find tag object of correct type"
DS_TERMINATE_FAILURE adm/admhusk/ds2acis/ds2acis.msg

"SDM failed to terminate"
DS_UNCONTAINED_CHILD adm/admhusk/ds2acis/ds2acis.msg

"Child's domain is not contained within parent's domain"
DS_UNDELETABLE_CSTRN adm/admhusk/ds2acis/ds2acis.msg

"can't remove cstrn - it is undeletable"
DS_UNEVEN_LINK_SPEEDS adm/admhusk/ds2acis/ds2acis.msg

"The speed, dC1/ds=a*dC2/ds, between a link_cstrn's dcrvs must be linearly related"
DS_UNINIT_DOMAIN_DIR adm/admhusk/ds2acis/ds2acis.msg

"Domain direction is uninitialized - see DM_set_cstrn_pttan_uv_dir()"
DS_UNKNOWN_ERROR adm/admhusk/ds2acis/ds2acis.msg

"The DM kernel signalled an unknown error - sorry"
DS_UNLABELLED_ERROR adm/admhusk/ds2acis/ds2acis.msg

"The DM kernel signalled an unlabeled error - sorry"
DS_UNSTOPABLE_CSTRN adm/admhusk/ds2acis/ds2acis.msg

"can't convert cstrn - it is unstopable"
DS_ZERO_ALPHA_AND_BETA adm/admhusk/ds2acis/ds2acis.msg

"Cannot have both alpha and beta equal to zero"
DS_ZERO_AREA_PATCH adm/admhusk/ds2acis/ds2acis.msg

"Cannot add a zero area patch to the hierarchy"
DS_ZERO_LENGTH_DOMAIN_DIR adm/admhusk/ds2acis/ds2acis.msg

"Domain_dir vector can not be zero length"
DUPLICATE_OPTION_NAME base/baseutil/option/option.msg

"Same name used for more than one option_header"
EARLIER_VERSION kern/kernel/kerndata/savres/savres.msg

"save file is from an earlier version of Acis"
EDGECOIN_PROBLEM bool/boolean/kernbool/boolean/boolean.msg

"system inconsistency processing edge coincidence"
EDGES_ALREADY_HAVE_ATTRIBS stitch/stchhusk/stitch/stchutil/stitchr.msg

"Input edges have stitch attributes already"
EDGE_ALREADY_STITCHED stitch/stchhusk/stitch/stchutil/stitchr.msg

"Input edge is already stitched"
EDGE_EDGE_COIN bool/boolean/kernbool/boolean/boolean.msg

"wire edge coincidences not yet implemented"
EDGE_FACE_COIN bool/boolean/kernbool/boolean/boolean.msg

"wire edge/face coincidences not yet implemented"
EDGE_HAS_DISCONTINUITY fct/faceter/api/facet.msg

"Edge has discontinuities, causing difficulties in meeting faceter tolerances."
EDGE_HAS_NO_FACE stitch/stchhusk/stitch/stchutil/stitchr.msg

"Input edge is connected to any face"
EDGE_NOT_FOUND intr/intersct/kerndata/raytest/raytest.msg

"failed to find an edge for find_shell_point"
EDGE_NOT_FREE covr/cover/sg_husk/cover/cover.msg

"only free edges can be processed."
EDGE_NO_VERT kern/kernel/kerndata/top/top.msg

"edge has a NULL vertex pointer"
EDGE_OFF_SURFACE covr/cover/sg_husk/cover/cover.msg

"Edge does not lie on the given surface"
EMPTY_ARRAY kern/kernel/kernapi/api/api.msg

"array with no members given"
EMPTY_EDGE_LIST cstr/constrct/kernwire/ewire/ewire.msg

"No edges supplied for new wire"
ENDS_NOT_DSTNCT kern/kernel/sg_husk/sweep/sweep.msg

"Cannot convert the profile to a valid sheet"
ENDS_TOO_CLOSE cstr/constrct/kernwire/wire/wire.msg

"end points of segment too close"
ENTITY_NOT_IN_STREAM kern/kernel/kerndata/bulletin/bulletin.msg

"entity is not in history stream"
ERROR_DURING_DISCARD kern/kernel/kerndata/bulletin/bulletin.msg

"error discarding a bad bulletin board, model state cannot be recovered. "
ERROR_DURING_MERGE kern/kernel/kerndata/bulletin/bulletin.msg

"error occured during bulletin board merge"
ERROR_DURING_ROLL kern/kernel/kerndata/bulletin/bulletin.msg

"error occured during roll"
ERROR_IN_FWRITE kern/kernel/kernutil/fileio/fileio.msg

"error writing to output stream"
EVALUATE_FAILED kern/kernel/kerngeom/curve/curve.msg

"AG curve evaluation failed"
EXACT_SUR_NO_BS3 kern/kernel/kerngeom/surface/surface.msg

"exact-spl-sur has no bs3-surface"
EXCEEDED_STACK_LIMIT base/baseutil/rtchecks/rtchecks.msg

"Exceeded stack limit"
EXCEED_MAX_CIRCUITS covr/cover/repair_husk/acovr.msg

"Exceed the maximum number of circuits"
EXCEPTION_DELETE_LEAK base/baseutil/mmgr/mmgr.msg

"Exception during construction causes possible memory leak"
EXCESSIVE_RECURSION base/baseutil/rtchecks/rtchecks.msg

"Excessive recursion"
EXPLODING_STEP kern/kernel/kerngeom/intcur/intcur.msg

"step size excessive when evaluating curve"
EXTENSION_TOO_BIG kern/kernel/kerngeom/intcur/intcur.msg

"cannot extend intcurve by more than current range"
FACES_SWEPT_AS_SOL kern/kernel/geomhusk/geomhusk.msg

"Faces always swept as solids."
FACE_BOUNDARY bool/boolean/kernbool/boolean/boolean.msg

"wire being deleted crosses face boundary"
FACE_IRREGULAR kern/kernel/sg_husk/api/sgapi.msg

"twisted or scrunched up face"
FACE_NOT_LAMINA kern/kernel/sg_husk/sweep/sweep.msg

"Swept face not a lamina for complete sweep"
FACE_NOT_MADE swp/sweep/kernwire/sweeping/sweeping.msg

"failed to make a face"
FACE_NO_GEOMETRY bool/boolean/kernbool/boolean/boolean.msg

"faces with no geometry encountered and ignored"
FACE_SELF_INTER kern/kernel/sg_husk/api/sgapi.msg

"self-intersecting face"
FAC_MAX_NPTS kern/kernel/spline/agspline/sg_bs3c/sg_bs3c.msg

"max npts exceeded and facets may not cover edge"
FAILED_LIBRARY_LOAD phlv5/phlv5_husk/sg_husk/phlv5/phlv5.msg

"Failed to load cattessellation.dll"
FF_MERGE_FAILURE intr/intersct/kerndata/makeint/makeint.msg

"failure in face-face intersection merging algorithm"
FIT_NO_KNOT_SPAN kern/kernel/spline/agspline/bs3_crv/bs3_crv.msg

"attempt to fit curve to zero knot span"
FIT_NO_SPAN kern/kernel/spline/agspline/bs3_crv/bs3_crv.msg

"attempt to fit curve to zero or one points"
FREELIST_IN_USE base/baseutil/mmgr/mmgr.msg

"ACIS memory still in use after api_stop_modeller"
FREE_COIN_BAD bool/boolean/kernbool/boolean/boolean.msg

"free edge coincidence list with other than two entries"
FREE_NODE_OFF_SIDE kern/kernel/meshhusk/mesh/mesh.msg

"ATTRIB_NODE not on triangle side"
FREE_STORE_OVERFLOW base/baseutil/mmgr/mmgr.msg

"free store overflow"
FUNCTION_NOT_IMPLEMENTED fct/faceter/api/facet.msg

"Function not implemented in derived mesh manager class"
GENERAL_CATIA_FAILURE phlv5/phlv5_husk/sg_husk/phlv5/phlv5.msg

"Internal Hidden Line Removal Error"
GRAPH_BAD_EDGE law/lawutil/main_law.msg

"A bad edge was added to a graph"
GRAPH_MISS_EDGE law/lawutil/main_law.msg

"The edge was not in the graph"
GRAPH_MISS_VERTEX law/lawutil/main_law.msg

"The vertex was not in the graph"
GRAZING_VERT_SMOOTH intr/intersct/kerndata/makeint/makeint.msg

"angle vertex measured as smooth"
HISTORY_SYNC kern/kernel/kerndata/savres/savres.msg

"not at eof after restoring history"
HM_BULLETIN_NOT_DISTRIBUTED kern/kernel/sg_husk/history/history.msg

"distribute cannot find a place for everything"
HM_DISTRIBUTE_OPEN_BB kern/kernel/sg_husk/history/history.msg

"distribute when open bulletin board exists"
HM_ENTITY_IN_TWO_STREAMS kern/kernel/sg_husk/history/history.msg

"Entity in two different copy scans causes ambibuous distribute"
HM_ENTITY_NOT_IN_STREAM kern/kernel/sg_husk/history/history.msg

"distribute entity to stream it was not created in"
HM_RESTORE_ERROR kern/kernel/sg_husk/history/history.msg

"Could not restore history"
HM_SAVE_DURING_DELETE kern/kernel/sg_husk/history/history.msg

"Attempt to save history while deleting it"
HM_SAVE_EARLY_VERSION kern/kernel/sg_husk/history/history.msg

"Cannot save history in save format earlier than 1.5"
HM_SAVE_ERROR kern/kernel/sg_husk/history/history.msg

"Could not save history"
HM_SAVE_UNLINKED_STREAM kern/kernel/sg_husk/history/history.msg

"Attempt to save history without delta state links"
ID_OVERFLOW kern/kernel/kernutil/fileio/fileio.msg

"entity identifier in save file too long"
ILLEGAL_BULLETIN_CHANGE kern/kernel/kerndata/bulletin/bulletin.msg

"changing bulletin entities pointers when non NULL"
ILLEGAL_DELETE kern/kernel/kerndata/data/data.msg

"direct deletion of ENTITY object not allowed"
ILLEGAL_ENTITY_DATA_ACCESS kern/kernel/kerndata/data/data.msg

"illegal entity data access - improper entity data type for operation"
ILLEGAL_ENTITY_FOR_SPLCONV bool/boolean/sg_husk/face/face.msg

"splconvert got a non-body, non-face"
ILLEGAL_ENTITY_MODIFICATION kern/kernel/kerndata/data/data.msg

"entity modification outside API_BEGIN/END block"
ILLEGAL_PCURVE_ENT kern/kernel/sg_husk/pcurve/sgpcurve.msg

"cannot add a pcurve to this entity"
ILLEGAL_SPLIT_SURF bool/boolean/sg_husk/split/split.msg

"can not split face with calculated surface"
ILLEGAL_SURFACE kern/kernel/kerngeom/splsur/splsur.msg

"Surface is illegal and cannot be evaluated"
ILLEGAL_WIRE_STITCH bool/boolean/sg_husk/stitch/stitch.msg

"Illegal attempt to stitch to a wire edge"
IMPROPER_SPLIT bool/boolean/sg_husk/boolean/sg_bool.msg

"Face(s) were not properly split"
INCOMPATIBLE_COEDS bool/boolean/sg_husk/stitch/stitch.msg

"Incompatible coedges encountered"
INCOMPATIBLE_CRV kern/kernel/spline/agspline/bs3_srf/bs3_srf.msg

"incompatible spline curves"
INCOMPLETE_WIRE bool/boolean/kernbool/boolean/boolean.msg

"intersection wire with dangling end"
INCONSISTENT_CFACE_CONTAINMENTS ct/ct_husk/compute/compute.msg

"Adjacent cfaces have inconsistent containments"
INCONSISTENT_LOOPS bool/boolean/kernbool/boolean/boolean.msg

"intersection loop inconsistent with body"
INCONS_ATTRIB bool/boolean/kernbool/boolean/boolean.msg

"coedge and edge attributes incompatible"
INCONS_AUX_INTS kern/kernel/kernint/intsfsf/intsfsf.msg

"inconsistent number of auxiliary intersections"
INCONS_BOX bool/boolean/kernbool/boolean/boolean.msg

"inconsistent face boxes - probably faulty edge boxing"
INCONS_COIN bool/boolean/kernbool/boolean/boolean.msg

"coincident intersection edge previously non-coincident"
INCONS_FACE bool/boolean/kernbool/boolean/boolean.msg

"inconsistent face-body relationships"
INCONS_GRAPH_VERTEX bool/boolean/kernbool/boolean/boolean.msg

"inconsistent graph vertices"
INCONS_INTS intr/intersct/sg_husk/query/query.msg

"Inconsistent intersection results. (Possible tolerance problem?)"
INCONS_INT_PTS kern/kernel/kernint/intsfsf/intsfsf.msg

"inconsistent numbers of silhouette ints"
INCONS_REL bool/boolean/kernbool/boolean/boolean.msg

"inconsistent edge-face relationships"
INCONS_SIDES bool/boolean/kernbool/boolean/boolean.msg

"inconsistent disposal values for double-sided face"
INCONS_VERT_ATT bool/boolean/kernbool/boolean/boolean.msg

"inconsistent information in vertex and coedge attributes"
INCONS_VERT_INT bool/boolean/kernbool/boolean/boolean.msg

"vertex intersection found but stored pointer NULL"
INCORRECT_RND_CHAMFER abl/abl_scm/ablscm.msg

"Need two-ends vradius for round-chamfer blend"
INDEXING_FAILED kern/kernel/kernutil/fileio/fileio.msg

"Sat file indexing mechanism failed while restoring the sat file"
INFINITE_INTERVAL kern/kernel/kernutil/fileio/fileio.msg

"cannot save infinite interval bound: large value used instead"
INFINITE_RECURSION intr/intersct/kernint/divcon/divcon.msg

"Subdivision too deep - possibly undiscovered branch point"
INPUT_NOT_AN_EDGE stitch/stchhusk/stitch/stchutil/stitchr.msg

"Input list has an entity which is not an EDGE"
INSIDE_WIRE kern/kernel/kerndata/convert/convert.msg

"Interior wires (wormholes) cannot be represented in pre-1.7 structures"
INSUFFICIENT_DATA kern/kernel/geomhusk/geomhusk.msg

"Not enough input arguments specified"
INSUFFICIENT_SPLGRID_DATA kern/kernel/geomhusk/geomhusk.msg

"Not enough data in splgrid."
INTERNAL_INCONS bool/boolean/kernbool/boolean/boolean.msg

"internal inconsistency in boolean operation"
INTERNAL_SNAP_ERROR covr/cover/repair_husk/bs3_snap.msg

"An internal error occured in during bs3 snapping"
INVALID_CIRCUITS covr/cover/repair_husk/acovr.msg

"Invalid circuits to cover"
INVALID_CT_MODEL ct/ct_husk/compute/compute.msg

"Cellular Topology structure is corrupt. Is topology okay?"
INVALID_ENTITY_REFRESH_LIST bool/boolean/kernapi/api/api_bool.msg

"The refresh list contains one or more entities from the seed element"
INVALID_GLUE_OPTS bool/boolean/kernapi/api/api_bool.msg

"Invalid glue options"
INVALID_HALF_ANGLE cstr/constrct/sg_husk/face/face_cstr.msg

"Cannot make a Cone with the given half angle"
INVALID_RADIUS abl/abl_scm/ablscm.msg

"Invalid radius function"
INVALID_SINGULARITIES cstr/constrct/sg_husk/face/face_cstr.msg

"Cannot make spline face with given singularities"
INVALID_STITCH_MAX_TOL stitch/stchhusk/stitch/stchutil/stitchr.msg

"Stitch max tol less than stitch min tol"
INVALID_STRING abl/abl_scm/ablscm.msg

"Unrecognized string"
INVALID_TYPE_REFRESH_LIST bool/boolean/kernapi/api/api_bool.msg

"The refresh list contained one or more invalid entity types"
ITER_LIMIT_CUR kern/kernel/kerngeom/intcur/intcur.msg

"exceeded iteration limit when evaluating curve"
KNOWN_REL bool/boolean/kernbool/boolean/boolean.msg

"outside relationship on wire being deleted"
LATER_VERSION kern/kernel/kerndata/savres/savres.msg

"save file is from a later version of Acis"
LAT_CURVE_NULL kern/kernel/sg_husk/sweep/sweep.msg

"Unable to construct Lateral curve"
LAT_SURF_INTER kern/kernel/sg_husk/sweep/sweep.msg

"Lateral surface would self-intersect. Try splitting profile."
LAT_SURF_NULL kern/kernel/sg_husk/sweep/sweep.msg

"Unable to compute the sweep surface"
LAWS_WARP_INCONSISTENT law/lawutil/main_law.msg

"A boundary vertex in a partial_space_warp is transformed to 2 different places"
LAW_ARCCOS law/lawutil/main_law.msg

"Out of the domain of the arccos [-1,1]"
LAW_ARCCOSH law/lawutil/main_law.msg

"Out of the domain of the arccosh x>=1"
LAW_ARCCOTH law/lawutil/main_law.msg

"Out of the domain of the arccoth x<-1 or x>1"
LAW_ARCCSC law/lawutil/main_law.msg

"Out of the domain of the arccsc x<-1 or x>1"
LAW_ARCCSCH law/lawutil/main_law.msg

"Out of the domain of the arccsch x!=0"
LAW_ARCSEC law/lawutil/main_law.msg

"Out of the domain of the arcsec x<-1 or x>1"
LAW_ARCSECH law/lawutil/main_law.msg

"Out of the domain of the arcsech 0<x<=1"
LAW_ARCSIN law/lawutil/main_law.msg

"Out of the domain of the arcsin [-1,1]"
LAW_ARCTANH law/lawutil/main_law.msg

"Out of the domain of the arctanh -1<x<1"
LAW_BAD_BOUNDS law/lawutil/main_law.msg

"The domain is not a finite interval"
LAW_BAD_DOMAN law/lawutil/main_law.msg

"The law function has an incorrect domain"
LAW_BAD_RAIL_LAW law/lawutil/main_law.msg

"The rail law is not perpendicular to the path"
LAW_BAD_RANGE law/lawutil/main_law.msg

"The law function has an incorrect range"
LAW_BAD_UNIT_VECTOR law/lawutil/main_law.msg

"The vector returned was not a unit vector"
LAW_BASE_C law/lawutil/main_law.msg

"Base must be a constant"
LAW_BASE_P law/lawutil/main_law.msg

"Base must be positive"
LAW_BEND_PARALLEL law/lawutil/main_law.msg

"Bending axis and direction are parallel."
LAW_COT law/lawutil/main_law.msg

"Out of the domain of the cot x!=n*pi"
LAW_COTH law/lawutil/main_law.msg

"Out of the domain of the coth x!=0"
LAW_CROSS_NUM law/lawutil/main_law.msg

"Too many parts to cross law"
LAW_CSC law/lawutil/main_law.msg

"Out of the domain of the csc x!=n*pi"
LAW_CSCH law/lawutil/main_law.msg

"Out of the domain of the csch x!=0"
LAW_DATA_CURVE law/lawutil/main_law.msg

"Law_data_curve eval too many derivatives"
LAW_DATA_PCURVE law/lawutil/main_law.msg

"Law_data_pcurve eval too many derivatives"
LAW_DATA_SAVE law/lawutil/main_law.msg

"Law_data type cannot save"
LAW_DATA_UNKNOWN law/lawutil/main_law.msg

"Unknown law_data type"
LAW_DATA_WIRE law/lawutil/main_law.msg

"Law_data_wire eval too many derivatives"
LAW_DEEP_COPY law/lawutil/main_law.msg

"This law may not be deep copied"
LAW_DERIV law/lawutil/main_law.msg

"Law class does not have a derivative function"
LAW_DIM law/lawutil/main_law.msg

"Bad law dimensions"
LAW_DIVISION law/lawutil/main_law.msg

"Right side of division must be a scalar"
LAW_DL_NUM law/lawutil/main_law.msg

"Wrong number of parts in derivative_law"
LAW_DOT_NUM law/lawutil/main_law.msg

"Too many parts to dot law"
LAW_EVAL law/lawutil/main_law.msg

"Law class does not have an evaluate function"
LAW_EVALDV law/lawutil/main_law.msg

"EvaluateDV does not return a vector"
LAW_EVALDV_ONE law/lawutil/main_law.msg

"EvaluateDV does not take one value"
LAW_EVALMMAT law/lawutil/main_law.msg

"EvaluateMMAT does not return a matrix"
LAW_EVALMT law/lawutil/main_law.msg

"EvaluateMT does not return a transf"
LAW_EVALS law/lawutil/main_law.msg

"EvaluateS was called on a multidimensional law"
LAW_EVALV law/lawutil/main_law.msg

"EvaluateV does not return a vector"
LAW_EVALVM law/lawutil/main_law.msg

"EvaluateVM does not return a vector"
LAW_EVALV_ONE law/lawutil/main_law.msg

"EvaluateV does not take one value"
LAW_EXPONENT law/lawutil/main_law.msg

"Out of domain of pow function"
LAW_LHOSPITAL law/lawutil/main_law.msg

"Division of zero by zero that cannot be resolved"
LAW_LN law/lawutil/main_law.msg

"Out of the domain of the natural log x>0"
LAW_LOG law/lawutil/main_law.msg

"Out of the domain of the log x>0"
LAW_MR law/lawutil/main_law.msg

"Value out of bounds in min_rotation_law"
LAW_MR_NUM law/lawutil/main_law.msg

"Wrong number of parts in min_rotation_law"
LAW_MULTI_CURVE_DOM law/lawutil/main_law.msg

"The total domain does not equal inputs"
LAW_NO_BSPLINE law/lawutil/main_law.msg

"The given curve or surface does not have a bspline approximation"
LAW_NO_INTR law/lawutil/main_law.msg

"The intr component is not linked in the executable"
LAW_NO_SAVE law/lawutil/main_law.msg

"Law may not be saved untill the next version"
LAW_POS_NUM law/lawutil/main_law.msg

"Wrong number of arguments in postrans law"
LAW_SAVE_APPROX law/lawutil/main_law.msg

"This has been saved as a b-spline"
LAW_SCALE_NUM law/lawutil/main_law.msg

"Wrong number of arguments in scaletrans law"
LAW_SEC law/lawutil/main_law.msg

"Out of the domain of the sec x!=pi*(n+.5)"
LAW_SQRT law/lawutil/main_law.msg

"Out of the domain of the sqrt x>0"
LAW_STEP_NUM law/lawutil/main_law.msg

"Wrong number of arguments in step law"
LAW_STEP_ODD law/lawutil/main_law.msg

"Odd member of step law is not constant"
LAW_STEP_ORDER law/lawutil/main_law.msg

"Steps constants are out of order"
LAW_SYMBOL law/lawutil/main_law.msg

"Law class does not have symbol function"
LAW_SYNTAX law/lawutil/main_law.msg

"Bad syntax"
LAW_TAN law/lawutil/main_law.msg

"Out of the domain of the tan x!=pi*(n+.5)"
LAW_TEST law/lawutil/main_law.msg

"One of the law test functions failed"
LAW_TIMES law/lawutil/main_law.msg

"One side of times must be a scalar"
LAW_TL_NUM law/lawutil/main_law.msg

"Wrong number of parts in coord_law"
LAW_TL_SYNTAX law/lawutil/main_law.msg

"Coord_law syntax error"
LAW_TWIST_NUM law/lawutil/main_law.msg

"Wrong number of parts in twist_law"
LAW_VARIABLE_RETURN law/lawutil/main_law.msg

"Return dim was called on a variable return law"
LAW_VEC_NUM law/lawutil/main_law.msg

"Wrong number of arguments in vectrans law"
LEFTOVER_STUFF_IN_REMESH kern/kernel/meshhusk/mesh/mesh.msg

"remesh did not use all trimming nodes or curves"
LESS_3_PTS cstr/constrct/kernwire/wire/wire.msg

"cannot make a closed kwire from fewer than 3 points"
LOOPING_FINDING_SEAM kern/kernel/meshhusk/surface/meshsur.msg

"getting stuck walking around a seam of a surface"
LOOP_BAD_SEP_CONTAIN kern/kernel/geomhusk/geomhusk.msg

"Containment fails on separator"
LOOP_BRIDGE cstr/constrct/kernwire/wire/wire.msg

"bridge to and from closed-edge vertex - not handled"
LOOP_CONE_DEGEN_NEAR_APEX kern/kernel/geomhusk/geomhusk.msg

"Degenerate loop is near the cone apex."
LOOP_CONE_ONE_SEP kern/kernel/geomhusk/geomhusk.msg

"Only one separation loop in cone"
LOOP_DEGEN kern/kernel/geomhusk/geomhusk.msg

"Containment checking is not performed on detected degenerate loops."
LOOP_EXTRA_PERI kern/kernel/geomhusk/geomhusk.msg

"More than one periphery loop"
LOOP_FACE_PARTIAL_BOUNDED kern/kernel/geomhusk/geomhusk.msg

"Face is not completely bounded."
LOOP_FACE_UNBOUNDED kern/kernel/geomhusk/geomhusk.msg

"Face is not bounded."
LOOP_HOLE_IN_HOLE kern/kernel/geomhusk/geomhusk.msg

"Hole contains hole"
LOOP_HOLE_NOT_CONTAINED kern/kernel/geomhusk/geomhusk.msg

"Hole is not contained"
LOOP_NOT_CLOSED kern/kernel/geomhusk/geomhusk.msg

"Open loop in face"
LOOP_NO_PERIPHERY kern/kernel/geomhusk/geomhusk.msg

"No periphery loop"
LOOP_PERI_WITH_SEP kern/kernel/geomhusk/geomhusk.msg

"Periphery exists with separation loop"
LOOP_SEP_IN_SPLINE kern/kernel/geomhusk/geomhusk.msg

"No prop edge on periodic spline face."
LOOP_TORUS_DEGEN_NEAR_APEX kern/kernel/geomhusk/geomhusk.msg

"Degenerate loop is near a torus apex. "
LOOP_TORUS_ONE_SEP kern/kernel/geomhusk/geomhusk.msg

"Only one separation loop in torus"
LOOP_TWO_PLUS_SEP kern/kernel/geomhusk/geomhusk.msg

"More than two separator loops"
LOPT_BAD_BOX lopt/lopt_husk/api/lopt.msg

"invalid box supplied"
LOPT_FREE_EDGE lopt/lopt_husk/api/lopt.msg

"free edge detected"
LOPT_INTERNAL lopt/lopt_husk/api/lopt.msg

"internal error"
LOPT_LAST_SHELL lopt/lopt_husk/api/lopt.msg

"only shell in body would be lost"
LOPT_NON_MANIFOLD lopt/lopt_husk/api/lopt.msg

"non-manifold edge detected"
LOPT_NOT_IMPLEMENTED lopt/lopt_husk/api/lopt.msg

"not yet implemented"
LOPT_TWK_BAD_OP_ON_ATT lopt/lopt_husk/api/lopt.msg

"invalid operation on lopt attribute"
LOP_BAD_BODY_TRANSFORM lop/lop_husk/api/lop.msg

"body transform has shear component"
LOP_BAD_BOX lop/lop_husk/api/lop.msg

"invalid box supplied"
LOP_HOL_ALL_OPEN lop/lop_husk/api/lop.msg

"all faces specified open"
LOP_HOL_BAD_VBL_OFFSET lop/lop_husk/api/lop.msg

"bad offset of a vertex blend"
LOP_HOL_MULTI_SHELL lop/lop_husk/api/lop.msg

"body to be hollowed has more than one shell"
LOP_MOVE_BAD_TRANSFORM lop/lop_husk/api/lop.msg

"invalid transform ( identity or non rigid body )"
LOP_NOT_IMPLEMENTED lop/lop_husk/api/lop.msg

"not yet implemented"
LOP_OFF_BAD_CURVATURE lop/lop_husk/api/lop.msg

"could not offset face because of bad curvature see err info"
LOP_OFF_BAD_MODEL_EXTENTS lop/lop_husk/api/lop.msg

"model is too large or is positioned outside the modeling space"
LOP_OFF_BAD_OFFSET lop/lop_husk/api/lop.msg

"offset null or will make body too thin or inside out"
LOP_OFF_NO_SURF lop/lop_husk/api/lop.msg

"could not offset surface as requested"
LOP_SWP_BAD_RAIL_OR_PATH lop/lop_husk/api/lop.msg

"path or rail information on swept face is bad"
LOP_TAP_BAD_ANGLE lop/lop_husk/api/lop.msg

"invalid taper angle"
LOP_TAP_BAD_EDGE lop/lop_husk/api/lop.msg

"edge has only one coedge"
LOP_TAP_BAD_NORMAL lop/lop_husk/api/lop.msg

"invalid taper plane normal"
LOP_TAP_BAD_PICK lop/lop_husk/api/lop.msg

"edge not on face it was picked with"
LOP_TAP_BAD_SURF lop/lop_husk/api/lop.msg

"cannot taper this surface type"
LOP_TAP_DUP_FACE lop/lop_husk/api/lop.msg

"face supplied more than once"
LOP_TAP_NOR_FACE lop/lop_husk/api/lop.msg

"face normal is at some point parallel to draft direction"
LOP_TAP_NO_ADJ_FACE lop/lop_husk/api/lop.msg

"adjacent face to vent face not found"
LOP_TAP_NO_SURF lop/lop_husk/api/lop.msg

"could not taper surface as requested"
LOP_TAP_TAN_EDGE lop/lop_husk/api/lop.msg

"edge tangent is at some point parallel to draft direction"
LOP_TWK_BAD_FACE lop/lop_husk/api/lop.msg

"face(s) supplied invalid, duplicate or from different bodies"
LOP_TWK_BAD_OP_ON_ATT lop/lop_husk/api/lop.msg

"invalid operation on lop attribute"
LOP_TWK_BAD_SURFACE lop/lop_husk/api/lop.msg

"invalid tool surface supplied"
LOP_TWK_COMPUTE_FAILED lop/lop_husk/api/lop.msg

"tweak compute failed"
LOP_TWK_FREE_EDGE lop/lop_husk/api/lop.msg

"free edge detected"
LOP_TWK_INTERNAL lop/lop_husk/api/lop.msg

"internal error"
LOP_TWK_MULTIPLE_EDGE lop/lop_husk/api/lop.msg

"multiple solutions for an edge"
LOP_TWK_MULTIPLE_VERT lop/lop_husk/api/lop.msg

"multiple solutions for a vertex"
LOP_TWK_NON_MANIFOLD lop/lop_husk/api/lop.msg

"non-manifold edge detected"
LOP_TWK_NO_BLEND_EDIT_SF lop/lop_husk/api/lop.msg

"blend edit unable to provide blend surface"
LOP_TWK_NO_EDGE lop/lop_husk/api/lop.msg

"no solution for an edge"
LOP_TWK_NO_FACE lop/lop_husk/api/lop.msg

"no faces supplied"
LOP_TWK_NO_LOOP lop/lop_husk/api/lop.msg

"no loop through new edges and vertices"
LOP_TWK_NO_VERT lop/lop_husk/api/lop.msg

"no solution for a vertex"
LOP_TWK_STACK_LIMIT lop/lop_husk/api/lop.msg

"stack limit exceeded"
LOP_TWK_TOPOL_CHANGE lop/lop_husk/api/lop.msg

"change in topology detected"
LOP_TWK_ZERO_LEN_EDGE lop/lop_husk/api/lop.msg

"open edge with coincident vertices generated"
LOST_ON_EDGE bool/boolean/kernbool/boolean/boolean.msg

"edge does not start or end at given vertex"
LOST_ON_LOOP bool/boolean/kernbool/boolean/boolean.msg

"loop does not contain given vertex"
MAKE_APPROX_CURVE_FAILED kern/kernel/kerngeom/curve/curve.msg

"failed to make required bspline curve approximation"
MAKE_APPROX_FAILED kern/kernel/kerngeom/surface/surface.msg

"failed to make required bspline approximation"
MAKE_APPROX_PCURVE_FAILED kern/kernel/kerngeom/pcurve/pcurve.msg

"failed to make required bspline pcurve approximation"
MAP_CONFUSION kern/kernel/kerndata/lists/lists.msg

"confusion in pointer pointer map"
MATH_DOMAIN base/baseutil/errorsys/errorbase.msg

"C math library: argument domain error"
MATH_ERROR base/baseutil/errorsys/errorbase.msg

"C math library error"
MATH_OVERFLOW base/baseutil/errorsys/errorbase.msg

"C math library: overflow range error"
MATH_PLOSS base/baseutil/errorsys/errorbase.msg

"C math library: partial loss of significance"
MATH_SING base/baseutil/errorsys/errorbase.msg

"C math library: argument singularity"
MATH_TLOSS base/baseutil/errorsys/errorbase.msg

"C math library: total loss of significance"
MATH_UNDERFLOW base/baseutil/errorsys/errorbase.msg

"C math library: underflow range error"
MATRIX_SINGULAR base/baseutil/vector/vector.msg

"attempt to invert a singular matrix"
MAX_GRID_LINES_EXCEEDED_ON_EDGE fct/faceter/api/facet.msg

"Edge tolerances not met because max_grid_lines is set too low"
MESH_HUSK_NOT_LINKED kern/kernel/kernint/intsfsf/intsfsf.msg

"all mesh intersectors are provided in the optional mesh husk"
MIDDLE_OF_UNDEFC kern/kernel/kerngeom/curve/curve.msg

"attempt to evaluate the middle of an undefined curve"
MISMATCHED_API_MACROS base/baseutil/rtchecks/rtchecks.msg

"API_END or API_NOP_END was bypassed (check for misplaced returns)"
MISMATCHED_EDGES bool/boolean/sg_husk/stitch/stitch.msg

"Edge stitching problem. Are duplicate edges present?"
MISMATCH_IN_OPTION heal/healhusk/util/healer.msg

"Mismatch in option between analyze and calculate phase"
MISSING_NEIGHBOR_ELEMENT kern/kernel/kernint/intsfsf/intsfsf.msg

"can't find adjacent element when intersection segment on element edge"
MISSING_OWNER_IN_UPDATE ct/ct_husk/compute/compute.msg

"Cface without owner in cell update"
MISSING_PCURVE intr/intersct/kerndata/ptinface/ptinface.msg

"coedge on parametric surface with no pcurve"
MISSING_SPAN_INFO bool/boolean/kernbool/boolean/boolean.msg

"span info missing for ef_int construction"
MISSING_SURF_ATT kern/kernel/meshhusk/mesh/mesh.msg

"surface element should have ATTRIB_SURFBACK but doesn't"
MITRE_PLANE_ZERO kern/kernel/sg_husk/sweep/sweep.msg

"Mitre plane normal, zero length"
MIXED_STREAMS kern/kernel/kerndata/bulletin/bulletin.msg

"combining multiple history streams"
MK_WIRE_BODY_FAIL cstr/constrct/geomhusk/geomhusk_cstr.msg

"Can't make wire body from given entity type"
MK_WIRE_BODY_NO_LOOP cstr/constrct/geomhusk/geomhusk_cstr.msg

"Face has no periphery loop to make wire body"
MULTIPLE_CIRCUITS covr/cover/repair_husk/acovr.msg

"Cannot handle multiple circuits"
MULTIPLE_ENT kern/kernel/kerndata/savres/savres.msg

"saving multiple entities as multiple single entity units"
MULTIPLE_WIRES kern/kernel/sg_husk/sweep/sweep.msg

"Multiple wires, too complex for sweep to handle"
MULTI_CALL intr/intersct/kerndata/makeint/makeint.msg

"call to int_loop_surf with non-null lists: calling function needs modification"
MULT_USE kern/kernel/kerngeom/curve/curve.msg

"attempt to transform a shared geometry"
NEED_PRUNE_PARTNERS kern/kernel/kerndata/bulletin/bulletin.msg

"cannot merge states without pruning partners"
NEGATIVE_MOMENT intr/intersct/kernbody/faceprop/faceprop.msg

"negative second moments - diagonals should always be positive"
NEG_VOLUME kern/kernel/sg_husk/sweep/sweep.msg

"Result of the sweep might be void"
NON_MANIFOLD_EDGE bool/boolean/kernbool/boolean/boolean.msg

"more than two faces at an edge of resulting body"
NON_NEG_LENGTH kern/kernel/kernapi/api/api.msg

"length not positive or zero"
NON_NEG_TOP kern/kernel/kernapi/api/api.msg

"top not positive or zero"
NON_POS_DEPTH kern/kernel/kernapi/api/api.msg

"depth negative or zero"
NON_POS_HEIGHT kern/kernel/kernapi/api/api.msg

"height negative or zero"
NON_POS_LENGTH kern/kernel/kernapi/api/api.msg

"length negative or zero"
NON_POS_RAD1 kern/kernel/kernapi/api/api.msg

"radius1 negative or zero"
NON_POS_RAD2 kern/kernel/kernapi/api/api.msg

"radius2 negative or zero"
NON_POS_TOP kern/kernel/kernapi/api/api.msg

"top negative or zero"
NON_POS_WIDTH kern/kernel/kernapi/api/api.msg

"width negative or zero"
NON_UNIQUE_CTRLPTS kern/kernel/sg_husk/api/sgapi.msg

"control points are not unique"
NON_UNIQUE_FITPTS kern/kernel/sg_husk/api/sgapi.msg

"coincident fit points"
NOTE_STATE_NR kern/kernel/kernapi/api/api.msg

"note_state: null result"
NOTE_UNBALANCED_BB kern/kernel/kerndata/bulletin/bulletin.msg

"note_state when bulletin board nesting unbalanced"
NOT_ALL_DERIVATIVES_FOUND kern/kernel/kerngeom/curve/curve.msg

"failed to obtain all derivatives requested"
NOT_ALL_INSIDE covr/cover/sg_husk/cover/cover.msg

"all connected coedges of wire must be of type: inside"
NOT_AN_ELLIPSE kern/kernel/geomhusk/geomhusk.msg

"The ENTITY is not an ellipse"
NOT_A_CURVE kern/kernel/geomhusk/geomhusk.msg

"ENTITY cannot be converted to a BOUNDED_CURVE"
NOT_A_LINE kern/kernel/geomhusk/geomhusk.msg

"The ENTITY is not a line"
NOT_BODY kern/kernel/kernapi/api/api.msg

"given pointer is not to a body"
NOT_BODY_RESTORE kern/kernel/kerndata/savres/savres.msg

"restore file does not contain a saved body"
NOT_COEDGE kern/kernel/kernapi/api/api.msg

"given pointer is not to a coedge"
NOT_COINC_PL swp/sweep/kernwire/sweeping/sweeping.msg

"planes not coincident"
NOT_CORRECT_TYPE kern/kernel/kernapi/api/api.msg

"given pointer is not to the correct entity type"
NOT_EDGE kern/kernel/kernapi/api/api.msg

"given pointer is not to an edge"
NOT_EXT_ED covr/cover/sg_husk/cover/cover.msg

"an edge of circuit is not external"
NOT_FACE kern/kernel/kernapi/api/api.msg

"given pointer is not to a face"
NOT_FACETED fct/faceter/api/facet.msg

"The target body is not faceted"
NOT_LAMINA kern/kernel/kernapi/api/api.msg

"given pointer is not to a lamina"
NOT_LINE_ME kern/kernel/kernapi/api/api.msg

"move edge only works with straight lines"
NOT_LOOP_COEDGE kern/kernel/kerndata/geometry/geometry.msg

"cannot find face from non-loop coedge"
NOT_LUMP kern/kernel/kernapi/api/api.msg

"given pointer is not to a lump"
NOT_ON_CURVE kern/kernel/geomhusk/geomhusk.msg

"Point given is not on curve."
NOT_PLANAR kern/kernel/geomhusk/geomhusk.msg

"Curves are not in the same plane"
NOT_PLANE kern/kernel/kernapi/api/api.msg

"given pointer is not to a plane"
NOT_PLANE_ME kern/kernel/kernapi/api/api.msg

"move edge only allows planar surfaces"
NOT_SAME_OWNER abl/abl_scm/ablscm.msg

"Input entities must belong to the same solid body"
NOT_SAME_PART scm/scmext/scmext.msg

"combining entities from different parts"
NOT_SHEET_BODY kern/kernel/kernapi/api/api.msg

"given pointer is not to a sheet body"
NOT_SHELL kern/kernel/kernapi/api/api.msg

"given pointer is not to a shell"
NOT_SOLID_EDGE kern/kernel/geomhusk/geomhusk.msg

"EDGE is not part of a solid"
NOT_SOLID_OWNER abl/abl_scm/ablscm.msg

"Given entity must belong to a solid body"
NOT_TOP_LEVEL kern/kernel/geomhusk/geomhusk.msg

"Cannot modify an ENTITY owned by another ENTITY"
NOT_TRANSFORM kern/kernel/kernapi/api/api.msg

"given pointer is not to a transformation"
NOT_TRANSFORMATION_ENTITY kern/kernel/geomhusk/geomhusk.msg

"Cannot apply transformation to entity"
NOT_VALID_ENTITY kern/kernel/geomhusk/geomhusk.msg

"Not a valid ENTITY type for this operation"
NOT_VERTEX kern/kernel/kernapi/api/api.msg

"given pointer is not to a vertex"
NOT_WIRE kern/kernel/kernapi/api/api.msg

"given pointer is not to a wire"
NOT_WIRE_BODY kern/kernel/kernapi/api/api.msg

"given pointer is not to a wire body"
NO_ANNOTATION kern/kern_scm/kern_scm.msg

"No ANNOTATION found matching the given criteria"
NO_AREA intr/intersct/kernbody/faceprop/faceprop.msg

"cannot calculate an area for this entity type"
NO_ATTRIB_INTCOED bool/boolean/kernbool/boolean/boolean.msg

"unexpected missing attribute on coedge"
NO_AUX_INT intr/intersct/kerndata/makeint/makeint.msg

"no intersection with auxiliary surface"
NO_BODIES_FOUND phlv5/phlv5_husk/sg_husk/phlv5/phlv5.msg

"No solid or sheet bodies found"
NO_BSPLINE kern/kernel/spline/agspline/bs3_crv/bs3_crv.msg

"unable to fit b-spline to given curve"
NO_CIRCUIT covr/cover/repair_husk/acovr.msg

"Cannot recognize a circuit"
NO_COEDGE abl/abl_scm/ablscm.msg

"No coedge for picked edge and face"
NO_CURVE_BOUNDS intr/intersct/kernint/intcusf/intcusf.msg

"intcusf with no curve bounds"
NO_CURVE_PERP kern/kernel/spline/agspline/bs3_crv/bs3_crv.msg

"no perpendicular from point to curve"
NO_CUR_BB kern/kernel/kerndata/bulletin/bulletin.msg

"no current bulletin board exists"
NO_CUR_DS kern/kernel/kerndata/bulletin/bulletin.msg

"no current delta state exists"
NO_EF_INTS bool/boolean/kernbool/boolean/boolean.msg

"no intersection records in find_graph_vertex"
NO_END_BOUND bool/boolean/kernbool/boolean/boolean.msg

"end bound for curve expected but missing"
NO_END_PT intr/intersct/kernint/divcon/divcon.msg

"No end for curve segment in divide-and-conquer"
NO_ENTS_FOUND abl/abl_scm/ablscm.msg

"No blendable entities found"
NO_FACE_BODY bool/boolean/sg_husk/split/split.msg

"face is not part of a body"
NO_FACE_NORMAL bool/boolean/kernbool/boolean/boolean.msg

"cannot find face normal for ordering coedges"
NO_GEN_INT kern/kernel/kernint/intsfsf/intsfsf.msg

"no generator/cone intersection when expected"
NO_GLX gl/gl_husk/gl_husk.msg

"No GLX Support detected on this X Server"
NO_GL_CONTEXT gl/gl_husk/gl_husk.msg

"Could not create the OpenGL Context"
NO_GL_VISUAL gl/gl_husk/gl_husk.msg

"Could not find a suitable XVisual"
NO_HISTORY scm/scmext/scmext.msg

"no history on requested part or entity"
NO_INSIDE_COED covr/cover/sg_husk/cover/cover.msg

"cannot find an inside coedge of wire"
NO_INTERSECTIONS kern/kernel/geomhusk/geomhusk.msg

"No intersections found between curves"
NO_INTERSECTION_EDGES bool/boolean/kernbool/boolean/boolean.msg

"no intersection edges"
NO_INTERSECTOR_FOUND intr/intersct/kernint/intcusf/intcusf.msg

"no appropriate curve-surface intersector was found"
NO_INTSCT bool/boolean/sg_husk/boolean/sg_bool.msg

"No intersection edges were found"
NO_INTSECT scm/scmext/scmext.msg

"no intersection"
NO_INT_POINT kern/kernel/kernint/intsfsf/intsfsf.msg

"cannot find intermediate intersection point"
NO_NEXT_EXT_ED covr/cover/sg_husk/cover/cover.msg

"cannot find next external edge"
NO_OUTSIDE_SHELL eulr/euler/kerndata/seplumps/seplumps.msg

"infinite body - no bounding shell found"
NO_PCURVE_LEFT intr/intersct/kerndata/ptinface/ptinface.msg

"no pcurve after trimming to edge range"
NO_PCURVE_ON_COEDGE bool/boolean/kernbool/boolean/boolean.msg

"a coedge on a spline surface doesn't have a pcurve"
NO_PRECISION intr/intersct/kernbody/faceprop/faceprop.msg

"error in second moments too large for meaningful results"
NO_PT_OFF_AXIS kern/kernel/sg_husk/sweep/sweep.msg

"Could Not find any point off Axis"
NO_QUADRATIC_ROOTS kern/kernel/kerngeom/splsur/splsur.msg

"no roots to quadratic equation for principal curvature"
NO_ROLLBACK kern/kernel/kerndata/data/data.msg

"changing unlogged record"
NO_SHOULDER kern/kernel/kernint/intsfsf/intsfsf.msg

"cannot find shoulder point for conic"
NO_SOLUTION_FOUND kern/kernel/geomhusk/geomhusk.msg

"No solution found"
NO_SPLINE_APPROX kern/kernel/kerngeom/splsur/splsur.msg

"unable to calculate spline approximation"
NO_SPLITTING_SURF bool/boolean/sg_husk/split/split.msg

"can not calculate splitting surface"
NO_START_BOUND bool/boolean/kernbool/boolean/boolean.msg

"start bound for curve expected but missing"
NO_START_PT intr/intersct/kernint/divcon/divcon.msg

"No start for curve segment in divide-and-conquer"
NO_STITCHABLE_GEOM bool/boolean/sg_husk/stitch/stitch.msg

"No identical edges or vertices in stitch bodies"
NO_SURFACE covr/cover/repair_husk/acovr.msg

"Surface cannot be created"
NO_SURF_PERP kern/kernel/spline/agspline/bs3_srf/bs3_srf.msg

"no perpendicular from point to surface"
NO_SW_EVAL_CURVATURE law/lawutil/main_law.msg

"sw_curve::eval_curvature not implemented"
NO_SW_LENGTH law/lawutil/main_law.msg

"sw_curve::length not implemented"
NO_SW_LENGTH_PARAM law/lawutil/main_law.msg

"sw_curve::length_param not implemented"
NO_SW_POINT_PERP law/lawutil/main_law.msg

"sw_curve::point_perp not implemented"
NO_TRIM_ITEM kern/kernel/geomhusk/geomhusk.msg

"Nothing specified to trim to"
NO_X_LAT_TOSUR kern/kernel/sg_husk/sweep/sweep.msg

"Lateral curve does not intersect to_surface"
NULL_ARRAY kern/kernel/kernapi/api/api.msg

"null pointer to array given"
NULL_ASSIGN kern/kernel/kerndata/data/data.msg

"writing to NULL data structure record"
NULL_BODY kern/kernel/kernapi/api/api.msg

"null pointer to body given"
NULL_COEDGE kern/kernel/kernapi/api/api.msg

"null pointer to coedge given"
NULL_CURVE_EVAL kern/kernel/spline/agspline/bs3_crv/bs3_crv.msg

"attempt to evaluate a null 3D spline curve"
NULL_DATUM_COEDGE bool/boolean/kernbool/boolean/boolean.msg

"NULL datum coedge"
NULL_DELTA kern/kernel/kernapi/api/api.msg

"null pointer to delta state given"
NULL_EDGE kern/kernel/kernapi/api/api.msg

"null pointer to edge given"
NULL_EDGE_VERTEX bool/boolean/kernbool/boolean/boolean.msg

"intersection edge with no start or end vertex"
NULL_ELEMENT kern/kernel/meshhusk/surface/meshsur.msg

"cannot determine element - is meshhusk linked into executable?"
NULL_ENTITY kern/kernel/kernapi/api/api.msg

"null pointer to entity given"
NULL_EXTENSION kern/kernel/kerngeom/intcur/intcur.msg

"attempt to extend null curve"
NULL_FACE kern/kernel/kernapi/api/api.msg

"null pointer to face given"
NULL_FACE_CREATED covr/cover/sg_husk/cover/cover.msg

"A face with NULL geometry created"
NULL_FACE_DERIV kern/kernel/kerndata/geometry/geometry.msg

"null face for finding derivatives"
NULL_FILE kern/kernel/kernapi/api/api.msg

"null file pointer given"
NULL_FREE base/baseutil/mmgr/mmgr.msg

"Attempt to free a NULL object"
NULL_GEOM_PTR kern/kernel/kernapi/api/api.msg

"given entity has a NULL geometry pointer"
NULL_LAW kern/kernel/kernapi/api/api.msg

"null law pointer given"
NULL_LUMP kern/kernel/kernapi/api/api.msg

"null pointer to lump given"
NULL_PARTNER_LOOP bool/boolean/kernbool/boolean/boolean.msg

"NULL partner loop"
NULL_PLANE kern/kernel/kernapi/api/api.msg

"null pointer to plane given"
NULL_SHELL kern/kernel/kernapi/api/api.msg

"null pointer to shell given"
NULL_STR kern/kernel/kernapi/api/api.msg

"null pointer to string given"
NULL_STREAM kern/kernel/kernapi/api/api.msg

"null pointer to history stream given"
NULL_STRING base/baseutil/errorsys/errorbase.msg

"NULL pointer passed to string function"
NULL_SURFACE kern/kernel/spline/agspline/bs3_srf/bs3_srf.msg

"NULL surface returned"
NULL_SURFACE_DERIV kern/kernel/kerndata/geometry/geometry.msg

"null surface for finding derivatives"
NULL_SURFACE_GEOM kern/kernel/kerndata/geometry/geometry.msg

"face without surface"
NULL_TEST_LOOP bool/boolean/kernbool/boolean/boolean.msg

"NULL test loop"
NULL_TRANSFORM kern/kernel/kernapi/api/api.msg

"null pointer to transformation given"
NULL_VERTEX kern/kernel/kernapi/api/api.msg

"null pointer to vertex given"
NULL_WIRE kern/kernel/kernapi/api/api.msg

"null pointer to wire given"
OFFSET_BRANCHED_WIRE ofst/offset/sg_husk/cur_off/cur_off.msg

"Cannot offset a branched wire"
OFF_SIDE_AND_NODE kern/kernel/meshhusk/mesh/mesh.msg

"ATTRIB_SURBACK should end on side or node but doesn't"
OLD_DOUBLE_SIDE kern/kernel/kerndata/top/top.msg

"pre-R1.5 faces all single-sided: double-sided information lost"
OLD_EDGE_PARAM kern/kernel/kerndata/top/top.msg

"pre_R1.1 curve parametrisation different: edge parameters may be wrong"
OLD_FIT_CUR kern/kernel/kerngeom/intcur/intcur.msg

"pre-R1.6 Acis unaware of fit curve: saved as exact spline"
OLD_INSIDE_WIRE kern/kernel/kerndata/top/top.msg

"pre-R1.7 wires were not classified inside/outside: inside lost"
OLD_MULTI_LUMP kern/kernel/kerndata/top/top.msg

"pre-R1.1 Acis cannot handle multiple lumps; first one only saved"
OLD_OFFSET_CUR kern/kernel/kerngeom/intcur/intcur.msg

"pre-R1.3 Acis unaware of offset intersection curve: saved as exact"
OLD_PAR2_CUR kern/kernel/kerngeom/intcur/intcur.msg

"pre-R1.5 Acis cannot evaluate parameter curve on surface 2: surfaces swapped"
OLD_PAR_CUR kern/kernel/kerngeom/intcur/intcur.msg

"pre-R1.3 Acis unaware of surface parameter curve: saved as surf_int_cur"
OLD_PIPE_SPLSUR kern/kernel/kerngeom/splsur/splsur.msg

"pre-R1.3 Acis unaware of special splines - pipe saved as exact spline"
OLD_PROJ_CUR kern/kernel/kerngeom/intcur/intcur.msg

"pre-R1.3 Acis unaware of projected curve: saved as surf_int_cur"
OLD_ROT_SPLSUR kern/kernel/kerngeom/splsur/splsur.msg

"pre-R1.3 Acis unaware of special splines - rotational surface saved as exact spline"
OLD_SAVE_REV kern/kernel/kerngeom/surface/surface.msg

"reversed spline(s) saved as unreversed before Release 1.3"
OLD_SHELL_WIRE kern/kernel/kerndata/top/top.msg

"pre-R1.7 wires do not belong to shells: connectivity lost"
OLD_SUM_SPLSUR kern/kernel/kerngeom/splsur/splsur.msg

"pre-R1.3 Acis unaware of special splines - sum surface saved as exact spline"
OLD_SURF2_CUR kern/kernel/kerngeom/intcur/intcur.msg

"pre-R1.5 Acis cannot evaluate surface curve on surface 2: surfaces swapped"
OLD_SURF_CUR kern/kernel/kerngeom/intcur/intcur.msg

"pre-R1.3 Acis surface curve may have only one surface saved"
OLD_TUBE_SPLSUR kern/kernel/kerngeom/splsur/splsur.msg

"pre-R1.3 Acis unaware of special splines - tube saved as exact spline"
ONLY_DOUBLE_USES intr/intersct/sg_husk/sense/sense.msg

"All faces are used twice. (Is this an open shell?)"
OPEN_FACE kern/kernel/sg_husk/sweep/sweep.msg

"One of the loops in the face is open"
OSCULATING_CURVES bool/boolean/kernbool/boolean/boolean.msg

"curves osculate at vertex - cannot evaluate order"
OUTSIDE_RANGE bool/boolean/kernbool/boolean/boolean.msg

"new ef_int outside edge"
OWNER_NOT_LOOP eulr/euler/kerndata/euler/euler.msg

"owner of coedge must be of type LOOP"
PARALLEL_SURF_DERIVS kern/kernel/kerngeom/intcur/intcur.msg

"surface u and v directions are parallel"
PARTIAL_COINCIDENCE kern/kernel/kernint/intsfsf/intsfsf.msg

"partial coincidence not implemented yet"
PAR_BAD_SURFACE intr/intersct/kernint/makesil/makesil.msg

"unknown surface type in make parameter lines"
PAR_CUR_SAVE_AS_APPROX kern/kernel/kerngeom/pcurve/pcurve.msg

"Saving par_cur as bspline approximation"
PATH_NOT_PLANAR kern/kernel/sg_husk/sweep/sweep.msg

"Sweep path not planar or degenerate"
PATH_OFF_PROF kern/kernel/sg_husk/sweep/sweep.msg

"Start of the path is not in the plane of the profile"
PATH_TANGENT kern/kernel/sg_husk/sweep/sweep.msg

"Path Curve tangential to the sweep profile"
PCURVE_WITHOUT_SURF kern/kernel/kerngeom/intcur/intcur.msg

"attempt to create an int_cur with a pcurve but no surface"
PCUR_TOO_SHORT eulr/euler/kerndata/euler/euler.msg

"given pcurve too short for edge"
PERP_SNAP covr/cover/repair_husk/bs3_snap.msg

"An attempt was made to snap the tangent of a bs3_curve by 90 degrees"
PHLV5_CAMERA_MISMATCH phlv5/phlv5_husk/sg_husk/phlv5/phlv5.msg

"Camera definitions not the same for all bodies"
PHL_CAMERA_MISMATCH phl/phl_husk/phl_func/phl_func.msg

"Camera definitions not the same for all bodies"
PHL_COMPUTE_FAILED phl/phl_husk/phl_func/phl_func.msg

"Could not compute hidden line data"
PLANE_NORMAL_ZERO kern/kernel/geomhusk/geomhusk.msg

"Cannot make Plane with zero length normal"
PM_CANNOT_OPEN_FILE part/part/pmhusk/pmhusk.msg

"cannot open file"
PM_HM_CANT_CHANGE_DISTRIBUTE_MODE part/part/pmhusk/pmhusk.msg

"History mode already established and cannot be changed"
PM_HM_HISTORY_CONFLICT part/part/pmhusk/pmhusk.msg

"attempt to merge history by moving entities between parts"
PM_HM_RESTORE_NOT_EMPTY part/part/pmhusk/pmhusk.msg

"Part not empty. History not restored"
PM_HM_RESTORE_UNDISTRIBUTED part/part/pmhusk/pmhusk.msg

"Not distributing history. History not restored"
PM_HM_SAVE_UNDISTRIBUTED part/part/pmhusk/pmhusk.msg

"Not distributing history. History not saved"
PM_NO_PART_NAME part/part/pmhusk/pmhusk.msg

"No part name set for PART::save"
PM_NO_STATE_TO_NAME part/part/pmhusk/pmhusk.msg

"attempt to name state when no state exists"
PM_UNBALANCED_STATES part/part/pmhusk/pmhusk.msg

"api_pm_start_state and api_pm_note_state unbalanced when balance expected"
POINT_IN_MESH_ERROR kern/kernel/meshhusk/surface/meshsur.msg

"point in mesh loop function did not succeed"
PROFILE_NOT_ON_PATH kern/kernel/sg_husk/sweep/sweep.msg

"No point on the path can be associated with the profile"
PROF_NOT_MITRE kern/kernel/sg_husk/sweep/sweep.msg

"The swept profile does not lie in the mitre plane at start of a closed path."
PROF_NOT_PLANAR kern/kernel/sg_husk/sweep/sweep.msg

"Sweep profile not planar"
PTRN_BAD_BUMP kern/kernel/kernapi/api/api.msg

"the face or loop to which the pattern was applied is not part of a valid bump or hole"
PTRN_FACE_NOT_CYLINDRICAL kern/kernel/kernutil/law/pattern.msg

"The specified face is not cylindrical"
PTRN_INCOMPATIBLE kern/kernel/kernapi/api/api.msg

"the pattern type is incompatible with the supporting face(s)"
PTRN_INCOMPATIBLE_DIM kern/kernel/kernutil/law/pattern.msg

"An incompatible dimension was specified"
PTRN_INCOMPLETE_ORIENTATION kern/kernel/kernutil/law/pattern.msg

"The pattern orientation is not completely specified"
PTRN_INVALID_ARGUMENT kern/kernel/kernutil/law/pattern.msg

"An invalid argument was specified"
PTRN_INVALID_DIM kern/kernel/kernutil/law/pattern.msg

"Dimensionality must be in the range of 1 to 3"
PTRN_INVALID_ENTITY kern/kernel/kernutil/law/pattern.msg

"An invalid entity type was specified"
PTRN_INVALID_KEEP kern/kernel/kernutil/law/pattern.msg

"A specified keep fraction cannot be negative, zero, or greater than one"
PTRN_INVALID_SCALE kern/kernel/kernutil/law/pattern.msg

"A specified scale value cannot be negative or zero"
PTRN_INVALID_SCALE_DIM kern/kernel/kernutil/law/pattern.msg

"A scale law must have either one or three dimensions"
PTRN_INVALID_SEED kern/kernel/kernutil/law/pattern.msg

"The seed used to find a bump must be a face or a loop"
PTRN_MISSING_ROOT kern/kernel/kernutil/law/pattern.msg

"A root position must be specified when the not_rotate option is used"
PTRN_NULL_ENTITY1 kern/kernel/kernutil/law/pattern.msg

"A NULL entity was specified"
PTRN_NULL_ENTITY2 kern/kernel/kernutil/law/pattern.msg

"A NULL entity was encountered"
PTRN_NULL_PATTERN kern/kernel/kernutil/law/pattern.msg

"A NULL pattern was specified"
PTRN_ORIENT_AXIS kern/kernel/kernutil/law/pattern.msg

"The associated axis must specified in the call to api_random_orient_pattern when the angular range is restricted"
PTRN_ORIENT_PARALLEL kern/kernel/kernutil/law/pattern.msg

"The vectors axis and start specified in the call to api_random_orient_pattern cannot be parallel or anti-parallel"
PTRN_ORIENT_PARALLEL1 kern/kernel/kernutil/law/pattern.msg

"The vectors normal and major_axis specified in the call to api_elliptical_pattern cannot be parallel or anti-parallel"
PTRN_OUT_BOUNDS kern/kernel/kernapi/api/api.msg

"one or more pattern elements was generated outside its containing entity"
PTRN_SELF_INTR kern/kernel/kernapi/api/api.msg

"some or all pattern-generated elements intersect with one another"
PTRN_SIZE_UNITY kern/kernel/kernutil/law/pattern.msg

"The pattern has only one element"
PTRN_ZERO_COUNT kern/kernel/kernutil/law/pattern.msg

"The number of pattern elements requested must be greater than zero"
PTRN_ZERO_ORIENT_RANGE kern/kernel/kernutil/law/pattern.msg

"The angle intervals passed to api_random_orient_pattern have zero range"
PT_OFF_SPLINE kern/kernel/spline/agspline/bs3_srf/bs3_srf.msg

"cannot evaluate parameter of point off spline"
PURE_VIRTUAL base/baseutil/errorsys/errorbase.msg

"call to a pure virtual member function"
RAIL_CURVE_NULL kern/kernel/sg_husk/sweep/sweep.msg

"Unable to compute the guide curve for sweep surface"
RAYINFACE_NO_HIT intr/intersct/kerndata/ptinface/ptinface.msg

"in-face ray misses intended loop"
RAYTEST_NO_HIT intr/intersct/kerndata/raytest/raytest.msg

"ray test failed to find intersection"
RBI_BAD_BOX rbi/rbi_husk/api/rbi.msg

"invalid box supplied"
RBI_BAD_FACE rbi/rbi_husk/api/rbi.msg

"face(s) supplied invalid, duplicate or from different bodies"
RBI_BAD_OP_ON_ATT rbi/rbi_husk/api/rbi.msg

"invalid operation on rbi attribute"
RBI_FREE_EDGE rbi/rbi_husk/api/rbi.msg

"free edge detected"
RBI_INTERNAL rbi/rbi_husk/api/rbi.msg

"internal error"
RBI_IRREP_FACE_LOOP rbi/rbi_husk/api/rbi.msg

"face loops not repairable"
RBI_NON_MANIFOLD rbi/rbi_husk/api/rbi.msg

"non-manifold edge detected"
RBI_NOT_4_COEDGES rbi/rbi_husk/api/rbi.msg

"not 4 coedges on intermediate non manifold edge"
RBI_NOT_IMPLEMENTED rbi/rbi_husk/api/rbi.msg

"not yet implemented"
RBI_NOT_IMPLEMENTED_FOR_CELL rbi/rbi_husk/api/rbi.msg

"rbi is not implemented for cellular topology"
RBI_NO_BODY rbi/rbi_husk/api/rbi.msg

"no body supplied"
RBI_NO_FACE rbi/rbi_husk/api/rbi.msg

"no faces supplied"
RBI_NO_LUMP_LEFT rbi/rbi_husk/api/rbi.msg

"no lumps left in body"
RBI_NO_SOLUTION rbi/rbi_husk/api/rbi.msg

"gap cannot be filled"
RBI_SELF_INT_FACE rbi/rbi_husk/api/rbi.msg

"self intersecting face"
RECORD_TYPE kern/kernel/kerndata/data/data.msg

"data structure record of unknown type"
REMOVE_NO_USECOUNT kern/kernel/kerndata/data/data.msg

"called remove() on entity with no use count"
REM_BAD_BOX rem/rem_husk/api/rem.msg

"invalid box supplied"
REM_BAD_FACE rem/rem_husk/api/rem.msg

"face(s) supplied invalid, duplicate or from different shells"
REM_FREE_EDGE rem/rem_husk/api/rem.msg

"free ( sheet ) edge detected"
REM_INTERNAL rem/rem_husk/api/rem.msg

"internal error"
REM_LAST_SHELL rem/rem_husk/api/rem.msg

"only shell in body would be lost"
REM_NON_MANIFOLD rem/rem_husk/api/rem.msg

"non-manifold edge or vertex detected"
REM_NOT_IMPLEMENTED rem/rem_husk/api/rem.msg

"not yet implemented"
REM_NO_EDGES rem/rem_husk/api/rem.msg

"no edges left to form solution"
REM_NO_FACE rem/rem_husk/api/rem.msg

"no faces supplied"
REM_NO_SOLUTION rem/rem_husk/api/rem.msg

"gap cannot be filled"
REM_TWO_LOOP rem/rem_husk/api/rem.msg

"network of removed faces has two loops"
REPAIR_INTERNAL covr/cover/repair_husk/repair.msg

"Internal repair husk error"
RESTORE_BAD_LONG kern/kernel/kernutil/fileio/fileio.msg

"attempt to read a true 64 bit long on a 32 bit platform"
RESTORE_EOF kern/kernel/kernutil/fileio/fileio.msg

"unexpected end of restore file"
RESTORE_NO_ENUM kern/kernel/kernutil/fileio/fileio.msg

"missing enumeration in restore file"
RESTORE_NO_INT kern/kernel/kernutil/fileio/fileio.msg

"missing integer in restore file"
RESTORE_NO_LOGICAL kern/kernel/kernutil/fileio/fileio.msg

"missing logical in restore file"
RESTORE_NO_REAL kern/kernel/kernutil/fileio/fileio.msg

"missing double in restore file"
RESULT_FACE_NOT_NULL covr/cover/repair_husk/acovr.msg

"Resulting FACE pointer must be NULL on input"
REVOLVE_NON_CIRCLE kern/kernel/sg_husk/sweep/sweep.msg

"To revolve around axis, the path must be circular."
RH_CE_ENVIRONMENT_END rbase/rnd_husk/intrface/intrface.msg

"env map preprocessing ends"
RH_CE_ENVIRONMENT_MEMORY rbase/rnd_husk/intrface/intrface.msg

"core env map memory failure"
RH_CE_ENVIRONMENT_START rbase/rnd_husk/intrface/intrface.msg

"preprocessing of env map"
RH_CE_INTERNAL rbase/rnd_husk/intrface/intrface.msg

"LightWorks internal error"
RH_CE_INVALID_CALL rbase/rnd_husk/intrface/intrface.msg

"core invalid LightWorks call"
RH_CE_INVALID_FILE rbase/rnd_husk/intrface/intrface.msg

"core invalid file format"
RH_CE_INVALID_SHADER rbase/rnd_husk/intrface/intrface.msg

"core incompatible shader"
RH_CE_MATHS rbase/rnd_husk/intrface/intrface.msg

"core maths error"
RH_CE_MEMORY rbase/rnd_husk/intrface/intrface.msg

"core general memory failure"
RH_CE_MISC rbase/rnd_husk/intrface/intrface.msg

"core miscellaneous error"
RH_CE_NONE rbase/rnd_husk/intrface/intrface.msg

"no error"
RH_CE_READ_FILE rbase/rnd_husk/intrface/intrface.msg

"core error reading file"
RH_CE_SHADOWS_END rbase/rnd_husk/intrface/intrface.msg

"shadow preprocessing ends"
RH_CE_SHADOWS_START rbase/rnd_husk/intrface/intrface.msg

"preprocessing of shadows"
RH_CE_SHADOW_MEMORY rbase/rnd_husk/intrface/intrface.msg

"core shadow memory failure"
RH_CE_SYSTEM rbase/rnd_husk/intrface/intrface.msg

"core system error"
RH_CE_TEXTURE_END rbase/rnd_husk/intrface/intrface.msg

"texture preprocessing ends"
RH_CE_TEXTURE_MEMORY rbase/rnd_husk/intrface/intrface.msg

"core texture memory failure"
RH_CE_TEXTURE_START rbase/rnd_husk/intrface/intrface.msg

"preprocessing of texture"
RH_CE_WRITE_FILE rbase/rnd_husk/intrface/intrface.msg

"core error writing file"
RH_IE_ARG_LMTEX rbase/rnd_husk/intrface/intrface.msg

"Internal shader argument list limit reached"
RH_IE_ARG_MISMATCH rbase/rnd_husk/intrface/intrface.msg

"Argument type doesn not match expected type"
RH_IE_ARG_UNKNOWN rbase/rnd_husk/intrface/intrface.msg

"Unknown shader argument"
RH_IE_BAD_HANDLE rbase/rnd_husk/intrface/intrface.msg

"Bad handle passed to function"
RH_IE_BCLS_CPY rbase/rnd_husk/intrface/intrface.msg

"copying render husk entity base class"
RH_IE_BCLS_IRES rbase/rnd_husk/intrface/intrface.msg

"saving render husk entity base class"
RH_IE_BCLS_ISAV rbase/rnd_husk/intrface/intrface.msg

"restoring render husk entity base class"
RH_IE_CPY_NULL rbase/rnd_husk/intrface/intrface.msg

"attempt to copy render entity with null handle"
RH_IE_CRT_FAIL rbase/rnd_husk/intrface/intrface.msg

"Failed to create render entity"
RH_IE_EMAP_SAVRES rbase/rnd_husk/intrface/intrface.msg

"Environment Map Save/Restore not currently supported"
RH_IE_ENTITY_MISMATCH rbase/rnd_husk/intrface/intrface.msg

"Entity type is wrong for requested operation"
RH_IE_NOT_INIT rbase/rnd_husk/intrface/intrface.msg

"render husk not initialised"
RH_IE_NULL_HANDLE rbase/rnd_husk/intrface/intrface.msg

"Null handle passed to function"
RH_IE_OP_INTERRUPT rbase/rnd_husk/intrface/intrface.msg

"Operation interrupted"
RH_IE_RST_ERR rbase/rnd_husk/intrface/intrface.msg

"Error restoring render entity"
RH_IE_SAV_ERR rbase/rnd_husk/intrface/intrface.msg

"Error saving render entity"
RH_IE_SHEAR_TRAN rbase/rnd_husk/intrface/intrface.msg

"Attaching Material to body with shear transform"
RH_IE_UNDEF_ERR rbase/rnd_husk/intrface/intrface.msg

"Unidentified render husk error"
RH_IE_UNKN_ARG rbase/rnd_husk/intrface/intrface.msg

"Argument not found for given shader"
RH_IE_UNKN_CVAR rbase/rnd_husk/intrface/intrface.msg

"Unknown control variable"
RH_IE_UNKN_FOTYPE rbase/rnd_husk/intrface/intrface.msg

"Out of range or Unknown Fall off type"
RH_IE_UNKN_LIMODE rbase/rnd_husk/intrface/intrface.msg

"Unknown internal mode"
RH_IE_UNKN_LITYPE rbase/rnd_husk/intrface/intrface.msg

"Unknown internal type"
RH_IE_UNKN_OMODE rbase/rnd_husk/intrface/intrface.msg

"Unknown output mode"
RH_IE_UNKN_RMODE rbase/rnd_husk/intrface/intrface.msg

"Unknown render mode"
RH_IE_UNKN_SHADER rbase/rnd_husk/intrface/intrface.msg

"Shader type not known for given shader class"
RH_SHADER_ARG_MISMATCH rbase/rnd_husk/entities/rh_ent.msg

"Adding Shader: Name already known, but different arg types"
RH_UE_BAD_COLOR_VAL rbase/rnd_husk/intrface/intrface.msg

"Out of range color val, RGB color values must be between 0.0 and 1.0"
RH_UE_BAD_REFLECT_VAL rbase/rnd_husk/intrface/intrface.msg

"Out of range refletion val, reflection factors must be between 0.0 and 1.0"
RH_UE_BAD_TRANSP_VAL rbase/rnd_husk/intrface/intrface.msg

"Out of range transparency val, transparency value must be between 0.0 and 1.0"
RIGID_W_DRAFT kern/kernel/sg_husk/sweep/sweep.msg

"Rigid sweep with draft"
ROLLED_SPATIAL_ENTITY kern/kernel/kerndata/bulletin/bulletin.msg

"access to non-user bulletin board entities is not allowed"
ROLL_DIRECTION_CONFUSED kern/kernel/kerndata/bulletin/bulletin.msg

"Roll direction not as expected"
ROLL_NULL_BB kern/kernel/kerndata/bulletin/bulletin.msg

"rollback given null bulletin board"
ROLL_OVER_ROOT kern/kernel/kerndata/bulletin/bulletin.msg

"Attempt to roll over root state"
ROOT_DS_LOST kern/kernel/kerndata/bulletin/bulletin.msg

"root state lost"
RUNTIME_SAFE_TYPE_CTOR base/baseutil/mthread/safe.msg

"runtime construction of a threadsafe type"
RUNTIME_SAFE_TYPE_DTOR base/baseutil/mthread/safe.msg

"runtime destruction of a threadsafe type"
SAVE_BAD_ENUM kern/kernel/kernutil/fileio/fileio.msg

"unknown value for enumeration in save"
SAVE_BAD_LONG kern/kernel/kernutil/fileio/fileio.msg

"attempt to write a true 64 bit long to a 32 bit file format"
SCHEME_ERROR scm/scheme/scheme.msg

"error processing scheme command"
SEGMENT_REVISITED kern/kernel/kernint/intsfsf/intsfsf.msg

"compcurv intersection segment processed twice"
SELF_INTER kern/kernel/sg_husk/sweep/sweep.msg

"The min radius of curvature is less than profile length"
SHEAR_INVERSE base/baseutil/vector/vector.msg

"attempt to invert a transform with shear"
SHEAR_SPHERE kern/kernel/kerngeom/surface/surface.msg

"attempt to shear a sphere"
SHEAR_TORUS kern/kernel/kerngeom/surface/surface.msg

"attempt to shear a torus"
SHEAR_TUBE kern/kernel/kerngeom/splsur/splsur.msg

"attempt to shear a tube surface"
SHEAR_UNIT base/baseutil/vector/vector.msg

"attempt to shear a unit vector"
SHEET_WITH_WIRE covr/cover/sg_husk/cover/cover.msg

"Cannot cover sheet body with wires"
SHELL_NOT_IN_LUMP kern/kernel/kernapi/api/api.msg

"shell is outside containing lump"
SHORT_GRAPH_EDGE bool/boolean/kernbool/boolean/boolean.msg

"graph edge is too short to make sense"
SIGAPOL_FAULT base/baseutil/errorsys/errorbase.msg

"Apollo-specific error"
SIGBUS_FAULT base/baseutil/errorsys/errorbase.msg

"bus error (illegal address)"
SIGFPE_FAULT base/baseutil/errorsys/errorbase.msg

"floating point exception"
SIGINT_FAULT base/baseutil/errorsys/errorbase.msg

"user interrupt"
SIGSEGV_FAULT base/baseutil/errorsys/errorbase.msg

"segmentation error"
SIGSOFT_FAULT base/baseutil/errorsys/errorbase.msg

"shared library error"
SIL_BAD_SURFACE intr/intersct/kernint/makesil/makesil.msg

"unknown surface type in make silhouettes"
SINGLE_COEDGE bool/boolean/kernbool/boolean/boolean.msg

"incomplete partner coedge ring"
SINGULAR_PARAM kern/kernel/kerngeom/surface/surface.msg

"attempt to evaluate curvature at parametric singularity"
SKIN_ALIGN_NONPLANAR kern/kernel/sg_husk/skin/skin.msg

"Cannot align non-planar wires."
SKIN_ALL_FACES_BAD kern/kernel/sg_husk/skin/skin.msg

"All lateral faces are degenerate."
SKIN_BAD_BOOLEAN_BRANCH kern/kernel/sg_husk/skin/skin.msg

"Could not boolean on or more of the tree branches"
SKIN_BAD_BOOLEAN_TRUNK kern/kernel/sg_husk/skin/skin.msg

"Could not boolean the trunk to the branches"
SKIN_BAD_BREAKUP kern/kernel/sg_husk/skin/skin.msg

"Breakup did not produce an equal number of coedges."
SKIN_BAD_FACE_LOFT kern/kernel/sg_husk/skin/skin.msg

"It was not possible to fix the face loft topology."
SKIN_BAD_GUIDE_CURVE kern/kernel/sg_husk/skin/skin.msg

"The guide curve is bad"
SKIN_BAD_LOFT_DIR kern/kernel/sg_husk/skin/skin.msg

"Lofting Bad loft take off direction found, perpendicular option was used to create the loft"
SKIN_BAD_MAPPING_CURVE kern/kernel/sg_husk/skin/skin.msg

"The mapping curve is bad"
SKIN_BAD_UV_SKIN_DIR kern/kernel/sg_husk/skin/skin.msg

"Surface U and V are in the same or opposite direction."
SKIN_BAD_UV_VALUE kern/kernel/sg_husk/skin/skin.msg

"Skin Evaluator called with Bad UV values"
SKIN_BAD_UV_VALUE_NET kern/kernel/sg_husk/net/net.msg

"Net Evaluator called with Bad UV values"
SKIN_BAD_VECTORS_AND_MAGNITUDES kern/kernel/sg_husk/skin/skin.msg

"Wrong number of vectors and/or magnitudes provided."
SKIN_BAD_WIRES kern/kernel/sg_husk/skin/skin.msg

"This is a bad choice of wires."
SKIN_BAD_WIRE_NORMAL kern/kernel/sg_husk/skin/skin.msg

"Encountered zero wire normal."
SKIN_BREAKUP_FORCED kern/kernel/sg_husk/skin/skin.msg

"Breakup was necessary."
SKIN_CANNOT_GET_MAPPING_CURVE kern/kernel/sg_husk/skin/skin.msg

"Cannot get the requested mapping curve."
SKIN_CLOSED_GUIDE_NOT_ALLOWED kern/kernel/sg_husk/skin/skin.msg

"A closed guide curve is not allowed if there are not at least three profiles."
SKIN_COEDGES_NOT_IN_ORDER kern/kernel/sg_husk/skin/skin.msg

"The coedges of a section are not in a sequence"
SKIN_COINCIDENT_COEDGES kern/kernel/sg_husk/skin/skin.msg

"Two coedges are coincident"
SKIN_CORRUPT_GUIDE_CURVE kern/kernel/sg_husk/skin/skin.msg

"Internal error, guide curve has become corrupt."
SKIN_FACE_HAS_SEAM kern/kernel/sg_husk/skin/skin.msg

"Face has a seam"
SKIN_G1_DISCONT_LOFT kern/kernel/sg_husk/skin/skin.msg

"Lofting G1 discontinuous sections, result will have gaps at vertices"
SKIN_GUIDE_CURVE_CROSSES kern/kernel/sg_husk/skin/skin.msg

"The guide curve crosses another guide curve"
SKIN_GUIDE_NOT_INTERSECT kern/kernel/sg_husk/skin/skin.msg

"The guide curve does not intersect all profiles"
SKIN_GUIDE_NOT_START_STOP kern/kernel/sg_husk/skin/skin.msg

"Guide curve does not start and stop on the first and last profile respectively."
SKIN_GUIDE_TRIMMED kern/kernel/sg_husk/skin/skin.msg

"Guide curve's end did not stop on the given profiles. Guide trimming was attempted."
SKIN_IDENTICAL_POSITIONS kern/kernel/sg_husk/skin/skin.msg

"Identical postions were detected during corner matching/alignment"
SKIN_LARGE_TOLERANCE kern/kernel/sg_husk/skin/skin.msg

"Large guide/profile gap exists due to using virtual guides when guide/profile distance is greater than resabs."
SKIN_LOFT_LAW_NON_FINITE_BOUNDS kern/kernel/sg_husk/skin/skin.msg

"A given law does not have a finite domain"
SKIN_LOFT_LAW_NOT_3D kern/kernel/sg_husk/skin/skin.msg

"A given law does not return three values"
SKIN_LOFT_LAW_NOT_SINGLE kern/kernel/sg_husk/skin/skin.msg

"A given law is not a single value function"
SKIN_LOFT_LAW_NO_BOUNDS kern/kernel/sg_husk/skin/skin.msg

"A given law does not have a domain"
SKIN_LOFT_RAD_CUR_LESS_RESFIT kern/kernel/sg_husk/skin/skin.msg

"Loft start or end radius of curvature is smaller than resfit"
SKIN_MAPPING_CURVES_ON_NONCLOSED_PROFILES kern/kernel/sg_husk/skin/skin.msg

"Mapping curves are only allowed on closed profiles"
SKIN_MAPPING_CURVE_INTERSECTION kern/kernel/sg_husk/skin/skin.msg

"The mapping curve intersects another mapping curve"
SKIN_MAPPING_CURVE_OFF_PROFILES kern/kernel/sg_husk/skin/skin.msg

"The mapping curve does not intersect a vertex on each wire profile"
SKIN_MULTI_LOOP_FACE kern/kernel/sg_husk/skin/skin.msg

"Face has more than one loop"
SKIN_NOT_ORIENTED kern/kernel/sg_husk/skin/skin.msg

"Skin surfaces could not be oriented"
SKIN_NOT_STITCHABLE_LOFT kern/kernel/sg_husk/skin/skin.msg

"The lofted surfaces could not be stitched"
SKIN_NO_NORMAL kern/kernel/sg_husk/skin/skin.msg

"Cannot determine the profile normal."
SKIN_NO_SIMPLIFY_ON_DRAFT kern/kernel/sg_husk/skin/skin.msg

"Unable to simplify wires when skinning with draft angles."
SKIN_PATH_INT_CROSS kern/kernel/sg_husk/skin/skin.msg

"Skin path intersections with profiles are not monotonic"
SKIN_PATH_PROFILE_NO_INT kern/kernel/sg_husk/skin/skin.msg

"Skin path does not intersect a profile plane"
SKIN_POINTS_NOT_ALLOWED kern/kernel/sg_husk/skin/skin.msg

"We currently do not support this functionality for point profiles."
SKIN_PROFILE_INTERSECTION kern/kernel/sg_husk/skin/skin.msg

"Intersecting profiles were detected."
SKIN_REDUNDANT_TWIST_VERTEX kern/kernel/sg_husk/skin/skin.msg

"Wires were merged: we do not remove minimize twist vertices that are redundant due to an overriding mapping curve."
SKIN_RULED_SURFACE_NOT_MADE kern/kernel/sg_husk/skin/skin.msg

"A ruled skin body was not made."
SKIN_SOLID_NOT_MADE kern/kernel/sg_husk/skin/skin.msg

"A solid body could not be made"
SKIN_TOO_FEW_COEDGE_LISTS kern/kernel/sg_husk/skin/skin.msg

"At least three distinct profiles are needed"
SKIN_VERTEX_NOT_FOUND kern/kernel/sg_husk/skin/skin.msg

"Temporary guide vertex was not found."
SKIN_VIRTUAL_OPT_BUT_NO_GUIDE kern/kernel/sg_husk/skin/skin.msg

"VirtualGuides was set to true but no guide curve was given."
SKIN_WIRES_NOT_ALIGNED kern/kernel/sg_husk/skin/skin.msg

"Opposing wire normals, incorrect wire alignment"
SKIN_WRONG_ALI_OPTION kern/kernel/sg_husk/skin/skin.msg

"Wrong align option given."
SKIN_WRONG_ARC_OPTION kern/kernel/sg_husk/skin/skin.msg

"Wrong arc_length option given."
SKIN_WRONG_BREAKUP_OPTION kern/kernel/sg_husk/skin/skin.msg

"Wrong match_vertices option given."
SKIN_WRONG_CLO_OPTION kern/kernel/sg_husk/skin/skin.msg

"Wrong closed option given."
SKIN_WRONG_MERGE_OPTION kern/kernel/sg_husk/skin/skin.msg

"Wrong merge_wirecoedges option given."
SKIN_WRONG_NO_TWIST_VERTS_OPTION kern/kernel/sg_husk/skin/skin.msg

"Wrong no_new_twist_vertices option given."
SKIN_WRONG_NTW_OPTION kern/kernel/sg_husk/skin/skin.msg

"Wrong no_twist option given."
SKIN_WRONG_PDC_OPTION kern/kernel/sg_husk/skin/skin.msg

"Wrong periodic option given."
SKIN_WRONG_PERP_OPTION kern/kernel/sg_husk/skin/skin.msg

"Wrong perpendicular option given."
SKIN_WRONG_SIM_OPTION kern/kernel/sg_husk/skin/skin.msg

"Wrong simplify option given."
SKIN_WRONG_SOL_OPTION kern/kernel/sg_husk/skin/skin.msg

"Wrong solid option given."
SKIN_WRONG_TANFACS_OPTION kern/kernel/sg_husk/skin/skin.msg

"Wrong estimate_loft_tanfacs option given."
SKIN_WRONG_VGS_OPTION kern/kernel/sg_husk/skin/skin.msg

"Wrong virtualGuides option given."
SKIN_ZERO_TANGENT_FACTOR kern/kernel/sg_husk/skin/skin.msg

"Zero Tangent factor at one section detected"
SLIVER_FACE bool/boolean/sg_husk/split/split.msg

"split face checking discovered a very small edge or face"
SMALL_LENGTH kern/kernel/kernapi/api/api.msg

"length is too small"
SMALL_RAD1 kern/kernel/kernapi/api/api.msg

"radius 1 is too small"
SMALL_RAD2 kern/kernel/kernapi/api/api.msg

"radius 2 is too small"
SMOOTH_W_DRAFT kern/kernel/sg_husk/sweep/sweep.msg

"Smooth sweep with draft"
SNAP_TO_DEGEN covr/cover/sg_husk/cover/cover.msg

"start and end point coincident, api_snap_edge does not snap edge to degnerate"
SPAN_EVAL kern/kernel/spline/agspline/bs3_crv/bs3_crv.msg

"error evaluating position/derivatives on span"
SPARE_SHELLS bool/boolean/kernbool/boolean/boolean.msg

"shells left in tool body"
SPINE_NOT_FIT kern/kernel/spline/agspline/bs3_srf/bs3_srf.msg

"attempt to make a tube with an exact spline spine"
SPINE_NOT_INTCURVE kern/kernel/spline/agspline/bs3_srf/bs3_srf.msg

"attempt to make a tube with an analytic spine"
SPLINE_EDGE intr/intersct/kerndata/raytest/raytest.msg

"raytest - cannot pick intersection edge yet"
SPLINE_SAVE_AS_EXACT kern/kernel/kerngeom/splsur/splsur.msg

"save version unaware of spline type - saved as exact spline"
SPLINE_SAVE_FAILURE kern/kernel/kerngeom/splsur/splsur.msg

"save version unaware of spline type"
SPLIT_ATTR_ERROR bool/boolean/kernbool/boolean/boolean.msg

"edge split attribute missing"
SPLIT_AT_END bool/boolean/kernbool/boolean/boolean.msg

"edge split at one end: maybe coincident geometries in input body"
SPUR_AT_BOTH_ENDS eulr/euler/kerndata/euler/euler.msg

"spur at both ends - not yet handled"
START_END_NULL kern/kernel/meshhusk/mesh/mesh.msg

"cannot handle a null starting or ending point"
STATE_NOT_IN_STREAM kern/kernel/kerndata/bulletin/bulletin.msg

"rollback state not in (correct) history stream"
STATE_NOT_ON_TRUNK kern/kernel/kerndata/bulletin/bulletin.msg

"rollback state not on history stream main branch"
STAT_NOT_INIT kern/kernel/kernapi/api/api.msg

"static class definitions not initialised"
STITCHING_FAILED stitch/stchhusk/stitch/stchutil/stitchr.msg

"Stitching could not be completed"
SUBSETTED_CURVE kern/kernel/kerngeom/curve/curve.msg

"save file version too early for bounded curve"
SUBTYPE_USE_COUNT_ERROR kern/kernel/kernutil/subtype/subtype.msg

"subtype use-count error"
SURFACE_INCORRIGIBLE covr/cover/repair_husk/repair.msg

"Surface incorrigible"
SURFACE_NOT_A_SPLINE covr/cover/repair_husk/acovr.msg

"Surface is not a spline"
SURF_BAD_CLOSURE kern/kernel/sg_husk/api/sgapi.msg

"surface closure is wrong"
SURF_NON_C1 kern/kernel/sg_husk/api/sgapi.msg

"surface is not C1"
SURF_NON_G0 kern/kernel/sg_husk/api/sgapi.msg

"surface is not G0"
SURF_NON_G1 kern/kernel/sg_husk/api/sgapi.msg

"surface is not G1"
SURF_NON_G2 kern/kernel/sg_husk/api/sgapi.msg

"surface is not G2"
SURF_OSC kern/kernel/spline/agspline/bs3_srf/bs3_srf.msg

"surface osculation at intersection"
SURF_POLE kern/kernel/spline/agspline/bs3_srf/bs3_srf.msg

"surface pole at intersection"
SWEEP_ADJACENT_FACE swp/sweep/sg_husk/api/sweepapi.msg

"Sweeping a sheet body only allows faces that are not adjacent."
SWEEP_BRANCHEDWIRE_NONSUPPORTED_OPTION swp/sweep/sg_husk/api/sweepapi.msg

"Sweeping a branched wirebody does not support draft, rigid, sweep to body or twist options"
SWEEP_BRANCHED_WIRE_BAD_PATH swp/sweep/sg_husk/api/sweepapi.msg

"Sweeping a branched wirebody requires a path with continuous tangency at arc segments"
SWEEP_CLOSE_NONPLANAR swp/sweep/sg_husk/api/sweepapi.msg

"Closing the profile to the axis has caused the profile to become non-planar."
SWEEP_DANGLING_WIRE kern/kernel/sg_husk/sweep/sweep.msg

"Cannot sweep dangling wires"
SWEEP_DEG_MULT_LOOP kern/kernel/sg_husk/sweep/sweep.msg

"Sweeping a multiple looped face with obsolete api."
SWEEP_DISTANCE_NOT_FACE swp/sweep/sg_husk/api/sweepapi.msg

"Only face can be swept with distance option."
SWEEP_DRAFT_NONPLANAR swp/sweep/sg_husk/api/sweepapi.msg

"Sweep with draft on non-planar profile."
SWEEP_DRAFT_NON_G1 swp/sweep/sg_husk/api/sweepapi.msg

"Cannot sweep with draft across a G0 path joint."
SWEEP_ELL_PROF_OFF_CENTER swp/sweep/sg_husk/api/sweepapi.msg

"The elliptical profile is slightly off center of the path. The profile is being moved to be exactly centered on the path."
SWEEP_FACE_NO_VEC swp/sweep/sg_husk/api/sweepapi.msg

"Can't identity sweep direction for the non-planar face."
SWEEP_HELIX_SELF_INT swp/sweep/sg_husk/api/sweepapi.msg

"The helical sweep results in a self-intersecting body."
SWEEP_INVALID_PATH swp/sweep/sg_husk/api/sweepapi.msg

"Path must be edge or wire-body."
SWEEP_INVALID_RESULT swp/sweep/sg_husk/api/sweepapi.msg

"Sweeping could not create a valid body."
SWEEP_LAW_SIZE_MISMATCH swp/sweep/sg_husk/api/sweepapi.msg

"Sweep law size does not match path segment number."
SWEEP_NEAR_TANGENT_PATH swp/sweep/sg_husk/api/sweepapi.msg

"Near tangency in the path requires use of tolerant edges."
SWEEP_NONPLANAR_FACE swp/sweep/sg_husk/api/sweepapi.msg

"Function operates on planar face only."
SWEEP_OFFSET_FACE_FAILS swp/sweep/sg_husk/api/sweepapi.msg

"Can't offset the planar face to valid body."
SWEEP_OLD_MITERS swp/sweep/sg_husk/api/sweepapi.msg

"Old miters were used."
SWEEP_OPEN_WIRE_TO_BODY swp/sweep/sg_husk/api/sweepapi.msg

"open wire bodies cannot be swept to face or body."
SWEEP_PATH_INVERTED swp/sweep/sg_husk/api/sweepapi.msg

"Direction of path has been inverted."
SWEEP_PORTION_TO_BODY swp/sweep/sg_husk/api/sweepapi.msg

"Can't sweep the specified portion with to_body option."
SWEEP_PORTION_UNKNOWN swp/sweep/sg_husk/api/sweepapi.msg

"Undefined sweep portion detected."
SWEEP_PROFILE_DISC_G1 swp/sweep/sg_husk/api/sweepapi.msg

"Profile is not C1 discontinuous"
SWEEP_PROFILE_NEAR_TANGENT swp/sweep/sg_husk/api/sweepapi.msg

"Sweeping with draft a near tangent profile."
SWEEP_PROFILE_NOT_ON_PATH swp/sweep/sg_husk/api/sweepapi.msg

"Can't locate profile on path."
SWEEP_PROF_DEGEN_AT_START swp/sweep/sg_husk/api/sweepapi.msg

"Can not move profile to path start due to degeneracy."
SWEEP_SCALE_TO_ZERO swp/sweep/sg_husk/api/sweepapi.msg

"Scale value can't be zero."
SWEEP_SELF_INT law/lawutil/main_law.msg

"The sweep results in self-intersecting surface"
SWEEP_SHEETBODY kern/kernel/sg_husk/sweep/sweep.msg

"Sweeping a sheetbody is not supported for rigid, twist or draft"
SWEEP_SHEETBODY_WARNING swp/sweep/sg_husk/api/sweepapi.msg

"Resulting body may contain self intersecting lumps."
SWEEP_SHEETBODY_WIRE kern/kernel/sg_husk/sweep/sweep.msg

"Sweeping a sheetbody containing wires is not supported with sweep_to_body"
SWEEP_TOL_EDGE_NO_MATCH swp/sweep/sg_husk/api/sweepapi.msg

"Could not insert tolerant edges as needed."
SWEEP_TO_FACE_OPTIONS swp/sweep/sg_husk/api/sweepapi.msg

"The sweep options bool_type, keep_law, and keep_branches are only applicable with sweep_to_body, not to_face."
SWEEP_UNBOUNDED kern/kernel/kerngeom/splsur/splsur.msg

"cannot sweep an unbounded curve"
SWEEP_UNDEFINED_DRAFT swp/sweep/sg_husk/api/sweepapi.msg

"Draft angle value is not allowed for sweeping."
SWEEP_VECTOR_NOT_CONSTANT_LAW swp/sweep/sg_husk/api/sweepapi.msg

"Only constant rail law and no twist can be used with vector option."
SWEEP_WIRE_IN_SHEETBODY_DRAFT swp/sweep/sg_husk/api/sweepapi.msg

"Draft and twist operations not allowed in wires from sheet bodies."
SWEEP_ZERO_LENGTH swp/sweep/sg_husk/api/sweepapi.msg

"Specified start and end point coincident"
SWEEP_ZERO_VECTOR swp/sweep/sg_husk/api/sweepapi.msg

"Attempt to sweep zero length vector."
SW_ANGLE_OR kern/kernel/sg_husk/sweep/sweep.msg

"sweep angle out of Range > 2*pi or < -2*pi"
SW_BAD_ORDER law/lawutil/main_law.msg

"A Bezier curve must be at least order 1"
SW_BAD_WEIGHTS law/lawutil/main_law.msg

"The weights of a Bezier curve must be strictly positive."
SW_SURFACE_EVAL law/lawutil/main_law.msg

"Attempt to evaluate an sw_surface outside its range"
TABLE_OVERFLOW base/baseutil/mmgr/mmgr.msg

"Cannot extend memory allocation table"
TANGENT_EVAL kern/kernel/kerngeom/intcur/intcur.msg

"unimplemented tangent track evaluation requested"
TCOEDGE_NO_PCURVE kern/kernel/kerndata/top/top.msg

"tcoedge has NULL pcurve pointer"
THREE_NEIGHBOURHOODS intr/intersct/kernint/divcon/divcon.msg

"Three curve ends in divide-and-conquer"
THUMBWTS_NOT_VALID abl/abl_scm/ablscm.msg

"Cannot have thumbwts with rnd_chamfer or elliptical rad types"
TIME_EXPIRED scm/scmext/scmext.msg

"time expired"
TINY_AREA intr/intersct/kernbody/faceprop/faceprop.msg

"area too small to calculate first and second moments"
TINY_VOLUME intr/intersct/kernbody/massprop/massprop.msg

"volume too small to calculate first and second moments"
TOLERANCE_CRUMBLE intr/intersct/kerndata/makeint/makeint.msg

"tolerance failure with coincident face_face_ints"
TOLERANCE_MISMATCH kern/kernel/kerndata/savres/savres.msg

"Tolerances of restored file do not match current tolerances"
TOL_ADD_TANG_TEDGE kern/kernel/kerndata/tolmod/tolmod.msg

"Tolerant modeling coincident intersection error"
TOL_BAD_EDGE_COUNT kern/kernel/kerndata/tolmod/tolmod.msg

"Unexpected number of edge on a tvertex"
TOL_BAD_PARAM kern/kernel/kerndata/tolmod/tolmod.msg

"Split parameter is outside the TCOEDGEs parameter range"
TOL_EDGE_NO_REPLACE bool/boolean/sg_husk/sliver/sliver.msg

"Edge not replaced because closed or in closed group or group exceeds tolerance"
TOL_INT_MISMATCH kern/kernel/kerndata/tolmod/tolmod.msg

"Tolerant intersection mismatch"
TOL_MOD_INCOMPATIBLE kern/kernel/kerndata/tolmod/tolmod.msg

"This function is not tolerant modeling compatible"
TOL_MOD_ZERO_RANGE_TEDGE kern/kernel/kerndata/tolmod/tolmod.msg

"Failed to make TEDGE because it would have had a zero parameter range"
TOO_FEW_SIDES kern/kernel/kernapi/api/api.msg

"too few sides (<3) requested"
TOO_MANY_AUX_INTS intr/intersct/kerndata/makeint/makeint.msg

"more than one intersection with aux surface"
TOO_MANY_ENTS kern/kernel/kerndata/savres/savres.msg

"more than one entity in file, only the first returned"
TOO_MANY_INTS kern/kernel/kernint/intsfsf/intsfsf.msg

"two intersections when one or none expected"
TOO_MANY_LOOPS eulr/euler/kerndata/euler/euler.msg

"trying to delete face with >1 loop"
TOP_BOT_INTER kern/kernel/sg_husk/sweep/sweep.msg

"Top and bottom profiles of sweep would intersect."
TO_CURVE_NULL kern/kernel/sg_husk/sweep/sweep.msg

"Unable to compute top curve"
TRIVIAL_CURVE kern/kernel/kernint/intsfsf/intsfsf.msg

"the points for fitting are all equal"
TWIST_NOT_PERP kern/kernel/sg_husk/sweep/sweep.msg

"Path not perpendicular to profile for sweep with twist"
UNACCEPTABLE_MODEL stitch/stchhusk/stitch/stchutil/stitchr.msg

"Bodies with inconsistencies cannot be healed"
UNBOUNDED_EDGE cstr/constrct/kernwire/ewire/ewire.msg

"Unbounded or single-point edge in wire"
UNCOVERABLE covr/cover/sg_husk/cover/cover.msg

"A loop of coedges cannot be covered"
UNDEF_COEDGE_GEOM intr/intersct/kernbody/faceprop/faceprop.msg

"parametric face has coedge with undefined geometry"
UNDEF_EDGE_GEOM intr/intersct/kernbody/faceprop/faceprop.msg

"face has edge with undefined geometry"
UNDEF_FACE_GEOM intr/intersct/kernbody/faceprop/faceprop.msg

"face has undefined geometry"
UNEXPECTED_EXCEPTION base/baseutil/errorsys/errorbase.msg

"Unexpected system exception"
UNEXPECTED_TAN intr/intersct/kerndata/makeint/makeint.msg

"edge tangent to intersection curve but not to surface"
UNFINDABLE_ENCLOSE_FACES ct/ct_husk/compute/compute.msg

"Could not find a valid enclose face for every cell."
UNIMPLEMENTED_CURVE kern/kernel/kerngeom/curve/curve.msg

"stream not yet provided for this type of curve"
UNIMPLEMENTED_MSH_SUR kern/kernel/meshhusk/surface/meshsur.msg

"unimplemented msh_sur type read"
UNIMPLEMENTED_REPARAM kern/kernel/kerngeom/surface/surface.msg

"unimplemented surface reparam() function called"
UNIMPLEMENTED_SURFACE kern/kernel/kerngeom/surface/surface.msg

"unimplemented surface type read"
UNIMPL_PCUR_CUR kern/kernel/kerngeom/intcur/intcur.msg

"unimplemented member function of pcur_int_cur called"
UNINITIALIZED_FREELIST base/baseutil/mmgr/mmgr.msg

"uninitialized freelist"
UNITS_NOT_EQUAL kern/kernel/kerndata/savres/savres.msg

"save units not equal to the restored units"
UNKNOWN_BS_CURVE kern/kernel/spline/agspline/bs3_crv/bs3_crv.msg

"unknown class of spline curve in save file"
UNKNOWN_BS_FORM kern/kernel/spline/agspline/bs3_srf/bs3_srf.msg

"unknown spline surface end form"
UNKNOWN_BS_SING kern/kernel/spline/agspline/bs3_srf/bs3_srf.msg

"unknown spline surface singularity type"
UNKNOWN_BS_SURFACE kern/kernel/spline/agspline/bs3_srf/bs3_srf.msg

"unknown class of spline surface in save file"
UNKNOWN_COLOR_MATERIAL rbase/rnd_husk/entities/entities.msg

"unknown color material component"
UNKNOWN_CURVE intr/intersct/kerndata/raytest/raytest.msg

"unknown curve type of edge"
UNKNOWN_DISPLACEMENT_MATERIAL rbase/rnd_husk/entities/entities.msg

"unknown displacement material component"
UNKNOWN_ELEMENT kern/kernel/meshhusk/mesh/mesh.msg

"element class is unknown to the mesh husk"
UNKNOWN_ENTITY kern/kernel/kerndata/savres/savres.msg

"unknown entity type(s) found"
UNKNOWN_FACE_CONT bool/boolean/kernbool/boolean/boolean.msg

"face containment cannot be determined"
UNKNOWN_GEOM intr/intersct/kernbody/faceprop/faceprop.msg

"face has an unrecognised geometry type"
UNKNOWN_REFLECTANCE_MATERIAL rbase/rnd_husk/entities/entities.msg

"unknown reflectance material component"
UNKNOWN_SCAN_TYPE kern/kernel/kerndata/data/data.msg

"called copy_scan() with unknown scan type"
UNKNOWN_SUBTYPE kern/kernel/kerndata/savres/savres.msg

"unknown entity subtype(s) found"
UNKNOWN_SUBTYPE_BINARY kern/kernel/kernutil/subtype/subtype.msg

"subtype object of unknown type in binary save file"
UNKNOWN_SUBTYPE_OLD kern/kernel/kernutil/subtype/subtype.msg

"subtype object of unknown type in old_style save file"
UNKNOWN_SURF intr/intersct/kerndata/raytest/raytest.msg

"unknown surface type of edgeless face"
UNKNOWN_SURFACE intr/intersct/kerndata/ptinface/ptinface.msg

"unknown surface for point-in-loop"
UNKNOWN_TOP_ENTITY kern/kernel/kerndata/savres/savres.msg

"unknown first entity type in restore file"
UNKNOWN_TRANSPARENCY_MATERIAL rbase/rnd_husk/entities/entities.msg

"unknown transparency material component"
UNMATCHED_POINT intr/intersct/kernint/divcon/divcon.msg

"Only one curve end in divide-and-conquer"
UNMERGEABLE_STATES kern/kernel/kerndata/bulletin/bulletin.msg

"states cannot be merged"
UNNOTED_STATE kern/kernel/kerndata/bulletin/bulletin.msg

"rollback from unnoted state"
UNREASONABLE_ARG base/baseutil/rtchecks/rtchecks.msg

"Unreasonable argument to math function"
UNRECOGNIZED_BDY_GEOM kern/kernel/kerngeom/d3_vbl/d3_vbl.msg

"Unrecognized type for BDY_GEOM read"
UNRECOGNIZED_RADIUS_FORM kern/kernel/sg_husk/vrbln/vrbln.msg

"Unrecognized radius form read"
UNSMOOTH_DRAFT kern/kernel/sg_husk/sweep/sweep.msg

"Adjacent Edges Not continuous for draft sweep"
UNTAGGED_INPUT kern/kernel/kerndata/data/data.msg

"untagged input for annotation"
UNTREAT_SING kern/kernel/sg_husk/api/sgapi.msg

"untreatable singularities in a surface"
U_WIRE_DEGENERATE kern/kernel/sg_husk/net/net.msg

"Net U interior Wire is degenerate"
U_WIRE_MULTI_COEDGE kern/kernel/sg_husk/net/net.msg

"Net U Wire contains more than one coedge"
VALUE_NEGATIVE kern/kernel/kernapi/api/api.msg

"value not positive or zero"
VALUE_NOT_POSITIVE kern/kernel/kernapi/api/api.msg

"value not positive"
VALUE_OUT_RANGE kern/kernel/kernapi/api/api.msg

"value out of range"
VALUE_ZERO kern/kernel/kernapi/api/api.msg

"value too close to zero"
VECTORS_NOT_PERP kern/kernel/kernapi/api/api.msg

"vectors not perpendicular"
VERTEX_INT intr/intersct/kerndata/makeint/makeint.msg

"make_ff_int: no start intersection in next coedge"
VERTEX_NOT_ON_EDGE intr/intersct/sg_husk/split/spled.msg

"input edge is not on the edge."
VERTEX_ON_EDGE_END intr/intersct/sg_husk/split/spled.msg

"split edge at vertex."
VRB_SAVE_APPROX kern/kernel/sg_husk/vrbln/vrbln.msg

"variable radius blend saved to old version as approximation"
V_WIRE_DEGENERATE kern/kernel/sg_husk/net/net.msg

"Net V interior Wire is degenerate"
V_WIRE_MULTI_COEDGE kern/kernel/sg_husk/net/net.msg

"Net V Wire contains more than one coedge"
WATCH_POINT base/baseutil/mmgr/mmgr.msg

"Interrupt at memory allocation watch point"
WIRES_NOT_COPLANAR covr/cover/sg_husk/cover/cover.msg

"wires are not co-planar"
WIRE_BODY_NOT_SUPPORTED heal/healhusk/util/healer.msg

"Wire bodies not supported in the Heal Husk"
WIRE_GRAZE bool/boolean/kernbool/boolean/boolean.msg

"wire grazing edge not yet implemented"
WIRE_HAS_BRANCH covr/cover/sg_husk/cover/cover.msg

"cannot cover a branched wire"
WIRE_MET covr/cover/sg_husk/cover/cover.msg

"wire edge met"
WIRE_NOT_CLOSED covr/cover/sg_husk/cover/cover.msg

"can only cover closed wires"
WIRE_NOT_IN_FACE bool/boolean/kernbool/boolean/boolean.msg

"wire not in any piece of subdivided face"
WIRE_NOT_PLANAR covr/cover/sg_husk/cover/cover.msg

"wire is not planar"
WIRE_SELF_INTERSECTS intr/intersct/sg_husk/utils/utils.msg

"Wire has self-intersection"
WIRE_X_AXIS kern/kernel/sg_husk/sweep/sweep.msg

"Self-intersection created by profile intersecting axis or crossing center of elliptical path."
WRONG_ENTITY_TYPE intr/intersct/kerndata/raytest/raytest.msg

"ray test hit unexpected entity type"
WRONG_INPUT abl/abl_scm/ablscm.msg

"Incorrect input: wrong number, order or type of arguments"
WRONG_LENGTH abl/abl_scm/ablscm.msg

"Input lists must have equal lengths"
WRONG_STATE kern/kernel/kerndata/bulletin/bulletin.msg

"rollback from incorrect system state"
ZERO_CONE cstr/constrct/sg_husk/face/face_cstr.msg

"Cannot make zero area Cone"
ZERO_DISTANCE kern/kernel/kernapi/api/api.msg

"distance too close to zero"
ZERO_FIT_INTCURVE kern/kernel/kerngeom/intcur/intcur.msg

"Encountered invalid intcurve without spline approximation"
ZERO_FIT_PCURVE kern/kernel/kerngeom/pcurve/pcurve.msg

"Invalid pcurve without spline approximation"
ZERO_LENGTH kern/kernel/kernapi/api/api.msg

"length too close to zero"
ZERO_LENGTH_AXIS kern/kernel/geomhusk/geomhusk.msg

"Zero length axis."
ZERO_LENGTH_EDGE kern/kernel/geomhusk/geomhusk.msg

"Cannot create zero length edge."
ZERO_NORMAL kern/kernel/kernapi/api/api.msg

"normal too close to zero"
ZERO_PLANE kern/kernel/geomhusk/geomhusk.msg

"Cannot make zero area Plane"
ZERO_PLANE_NORM kern/kernel/kerngeom/surface/surface.msg

"attempt to evaluate a plane with zero normal"
ZERO_SPHERE cstr/constrct/sg_husk/face/face_cstr.msg

"Cannot make zero area Sphere"
ZERO_TORUS cstr/constrct/sg_husk/face/face_cstr.msg

"Cannot make zero area Torus"
ZERO_TORUS_NORM kern/kernel/kerngeom/surface/surface.msg

"attempt to evaluate a torus with zero normal"
PDF/APPDEV/AERMSG.PDF
HTM/DATA/ACIS/APPDEV/AERMSG/0001.HTM